Prototyping & Wiring

SKU: SF-KIT-10547 | Brand: SparkFun

This is the latest version of our popular through-hole Simon Says Kit. We’ve made some changes to the board that should make it easier than ever for the beginner to build! All components are through-hole, making this ...

SKU: SF-COM-12877 | Brand: SparkFun

We know this looks like a lot of our other LEDs, but it’s not! This is a PTH Addressable RGB LED with a WS2812 control IC built right into the LED. This PTH version is incredibly similar to its SMD cousin, except it i...

SKU: PL-1907 | Brand: Pololu

These 1×8-pin crimp connector housings let you quickly build custom cables that mate with standard 0.1" (2.54mm) spaced connectors. Pair them with pre-crimped terminal wires to create reliable, removable eight-wire co...

SKU: PL-1905 | Brand: Pololu

These 1×6-pin crimp connector housings let you quickly build custom cables that mate with standard 0.1" (2.54mm) spaced connectors. Pair them with pre-crimped terminal wires to create reliable, removable six-wire conn...

SKU: DF-FIT0373 | Brand: DFRobot

INTRODUCTION   Are you still looking for a UHF RFID tag for your UHF RFID reader? Try this one! This RFID tag Alien higgs3 chip accords with ISO 18000-6C,EPC Class1 Gen2 standard protocol.Besides, it contains ...

SKU: DF-FIT0374 | Brand: DFRobot

INTRODUCTION Are you still looking for a UHF RFID tag for your UHF RFID reader? Try this one, this UHF tag accords with ISO 18000-6C,EPC Class1 Gen2 standard protocol. It contains 96 bit EPC...

SKU: DF-DFR0351 | Brand: DFRobot

INTRODUCTION Romeo BLE mini is a small Arduino compatible robot control board with motor driver and bluetooth 4.0. It benefits from the Arduino open source platform, which includes thousa...

SKU: SF-PRT-12807 | Brand: SparkFun

A standard 2×3 male through-hole header with 0.1″ (2.54 mm) pin spacing. This is the common configuration used for ISP (In-System Programming) connectors on AVR microcontroller boards and programmers. Key Features ...

SKU: SF-BOB-12758 | Brand: SparkFun

The SparkFun Electret Microphone Breakout pairs a small electret microphone capsule with a 60× OPA344 op-amp preamplifier, making it easy to detect sound with a microcontroller's analogue-to-digital converter. Pick up...

SKU: SF-SEN-10289 | Brand: SparkFun

This AT407 basic tilt switch can easily be used to detect orientation. Inside the can is a ball that make contact with the pins when the case is upright. Tilt the case over and the balls don’t touch, thus not making a...

SKU: SF-PRT-12639 | Brand: SparkFun

A 3.5mm TRRS (tip, ring, ring, sleeve) audio jack in a surface-mount package. Unlike standard stereo TRS connectors, TRRS provides three conductors plus ground, allowing it to carry stereo audio along with an addition...

SKU: DF-DFR0370 | Brand: DFRobot

The Arduino CAN BUS Shield V2 brings Controller Area Network (CAN bus) communication to your Arduino. Built around the MCP2515 CAN controller, it supports both standard and extended frames for transmitting and receivi...

SKU: AF-724 | Brand: Adafruit

Screw terminal blocks are the clean, maintainable solution for PCB-to-wire connections — no solder, no loose ends, easy to swap out later. These 3.5mm pitch 2-pin blocks are a practical size: wide enough for a range o...

SKU: AF-163 | Brand: Adafruit

A precision triple-axis accelerometer breakout featuring the Analog Devices ADXL335. With a ±3 g measurement range and analog outputs for X, Y, and Z axes, this sensor is ideal for tilt sensing, motion detection, and ...

SKU: SF-TOL-12572 | Brand: SparkFun

These are nice, cross-locking, curved tweezers, unlike traditional models the tips on these tweezers will remain closed until squeezed open. They have a very fine tip which allows you to pick up very small parts with ...

SKU: SF-DEV-09873 | Brand: SparkFun

The SparkFun FTDI Basic Breakout provides USB-to-serial conversion using the FTDI FT232RL IC, operating at 3.3V logic levels. Its 6-pin header matches the standard FTDI pinout, making it compatible with Arduino Pro, L...

SKU: SF-CAB-09741 | Brand: SparkFun

These are good quality IC test hooks with a male connection wire. Instead of a single hook, these have two hooks that are capable of grabbing very small points (like SOIC IC legs). Comes in a bag of five IC hooks of d...

SKU: DF-DRI0039 | Brand: DFRobot

INTRODUCTION The latest quad motor driver shield for Arduino, compatible with 5V/3.3V Arduino controller, can control up to four DC motors with 8 pins at the same time. The shield supports P...

SKU: DF-DFR0012 | Brand: DFRobot

The Arduino Nano I/O Sensor Shield acts as an expansion board for the Arduino Nano and DFRduino Nano microcontrollers. There are several different options for power input. The form factor of the Nano I/O Shield bo...

SKU: AF-816 | Brand: Adafruit

These right-angle male headers feature a 3-row configuration at standard 0.1" (2.54mm) pitch, making them ideal for connecting three-wire cables such as sensor and servo leads. Each piece is a 3×4 block, and four piec...