Prototyping & Wiring

SKU: SF-WRL-23319 | Brand: SparkFun

The Arduino GIGA R1 WiFi is a powerful development board built around the STM32H747XI dual-core microcontroller, featuring a Cortex-M7 at 480 MHz and a Cortex-M4 at 240 MHz. With 2 MB flash and 1 MB RAM, it handles de...

SKU: SF-SEN-23352 | Brand: SparkFun

QR codes are a great way for users to communicate with microcontrollers, whether it’s passing WiFi credentials to set up connectivity or sending personal information to fill out a digital badge. Reading them from a ma...

SKU: DF-DFR1056 | Brand: DFRobot

Note: The Arduino GIGA R1 WiFi Development Board is available for pre-order and is expected to be shipped in late September. This Arduino GIGA R1 WiFi Development Board measures only 101 x 53mm and has the same for...

SKU: DF-SEN0570 | Brand: DFRobot

Fermion: MEMS Smoke Gas Detection Sensor employs state-of-the-art microelectromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat...

SKU: DF-SEN0571 | Brand: DFRobot

Fermion: MEMS Odor Smell Gas Detection Sensor employs state-of-the-art microelectromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal...

SKU: DF-SEN0567 | Brand: DFRobot

Fermion: MEMS Ammonia NH3 Gas Detection Sensor employs state-of-the-art micro-electromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minim...

SKU: LB-732-2865-ND | Brand: Little Bird

A 10-position single-row right-angle header with gold-plated pins at standard 2.54mm (0.1") pitch. Through-hole mounting for PCB soldering, with pins oriented at 90° for horizontal mating with female connectors or jum...

SKU: SF-CAB-22036 | Brand: SparkFun

An RP-SMA (Reverse Polarity Sub-Miniature A) extension cable with male-to-female connectors and RG174 coaxial housing. Ideal for mounting an antenna to the outside of an enclosure while keeping the electronics inside....

SKU: LB-COCKATOO | Brand: Little Bird

The Cockatoo is a simple screw-terminal breakout board for the BBC micro:bit. Slide your micro:bit into the edge connector and you get secure screw terminal access to pins 0, 1, 2, 3.3V, and GND — no soldering or croc...

SKU: SF-CAB-22037 | Brand: SparkFun

A 25cm RP-SMA male-to-female extension cable with RG174 coaxial housing. Ideal for repositioning an antenna to the outside of an enclosure while keeping your electronics neatly inside, this cable provides a reliable R...

SKU: AF-5709 | Brand: Adafruit

The Adafruit CAN Bus FeatherWing adds CAN bus networking to any Feather board. It uses the MCP2515 CAN controller and TJA1051/3 transceiver to send and receive messages in standard or extended format at up to 1 Mbps o...

SKU: SF-DEV-21247 | Brand: SparkFun

The SparkFun USB-C Host Shield provides all the digital logic and analogue circuitry needed to add USB peripheral/host control to your Arduino. Interface with and control any USB 2.0 compatible device — thumb drives, ...

SKU: DF-DFR0979 | Brand: DFRobot

The Gravity CH423 I2C 24 Digital IO Expansion Module extends your microcontroller with 24 additional digital output/input pins over a standard I2C connection. Based on the CH423 chip, it provides 8 GPIOs with interrup...

SKU: AF-5652 | Brand: Adafruit

Some days we're feeling extra fancy here at the 'fruit warehouse, and we have a big soft spot for woven fabric cables. Like, peep this fully reversible pink/purple Blinka-inspired cable or this mithril-like 3-in-1 Syn...

SKU: AF-5663 | Brand: Adafruit

Need to use multiple I2C devices that share the same address? The PCA9546 4-Channel I2C Multiplexer lets you connect up to four same-address I2C devices to a single microcontroller by acting as a gatekeeper — write a ...

SKU: DF-FIT0903 | Brand: DFRobot

The cable is compatible with LattePanda 2 Alpha&Delta, and&nbsp;LattePanda 3 Delta 864.With the DC 5.5x2.1mm Power Cable, LattePanda can be powered by a common 12V DC power supply or a 12V battery pack easily. Feat...

SKU: AF-5611 | Brand: Adafruit

The Adafruit PCF8575 GPIO Expander Breakout is an affordable 16-channel I2C GPIO expander that doubles your available digital I/O over a simple two-wire connection. Add extra buttons, LEDs, relays, or other digital pe...

SKU: AF-5610 | Brand: Adafruit

The Adafruit LTR-303 is a low-cost I2C digital light sensor that provides 16-bit measurements for both infrared and visible+IR spectrums. Subtract one from the other to get human-visible light readings. With configura...

SKU: AF-5497 | Brand: Adafruit

We now have a handy extension cord for JST-XH projects!&nbsp;One end has a JST-XH&nbsp;socket, and the other has a matching plug. Between the two, 500mm of color-coded wire.&nbsp;This solid 2.5mm pitch connector exten...

SKU: AF-5532 | Brand: Adafruit

Have you found yourself in a maze of twisty-turny knobs, all alike? These micro potentiometer&nbsp;(or rotary encoder) knobs offer a rainbow burst of color to your synth or control panel. They are made of a hard plast...