Prototyping & Wiring

SKU: SF-COM-11451 | Brand: SparkFun

These color-changing LEDs take the work out of creating crazy, flashy, blinky… ness. Simply apply power and the LED will cycle through the RGB colorspace: no external controller necessary! These bright and festive ...

SKU: DF-SEN0170 | Brand: DFRobot

A three-cup anemometer kit with 0–5V analog voltage output for building custom weather stations and wind monitoring systems. The aluminium alloy construction provides high strength, weather resistance, and corrosion r...

SKU: AF-3133 | Brand: Adafruit

The Adafruit Ultimate GPS FeatherWing brings precise, low-power GPS to the Feather ecosystem. Built around the MTK3339 chipset, it tracks up to 22 satellites on 66 channels with -165 dBm sensitivity and delivers up to...

SKU: AF-238 | Brand: Adafruit

This is a interface cable designed for Bus Pirate which can makes it easier to connect the Bus Pirate to a circuit and get hacking!

SKU: SF-BOB-13601 | Brand: SparkFun

Are you low on I/O? No problem! The SX1509 Breakout is a 16-channel GPIO expander with an I2C interface – that means with just two wires, your microcontroller can interface with 16 fully configurable digital input/...

SKU: AF-3083 | Brand: Adafruit

A compact aluminium heatsink with pre-applied thermal adhesive for easy installation on the Raspberry Pi 3 and other single board computers. Simply peel off the protective film and press firmly onto the processor — no...

SKU: SF-PRT-11366 | Brand: SparkFun

This is the Big Red Box! These beefy, bright red, flanged, plastic enclosures will give your widget the protection (and attention) it deserves. You’ve probably seen these used to enclose radio equipment or antenna bal...

SKU: SF-PRT-11363 | Brand: SparkFun

A set of three common gauges of enameled magnet wire for winding transformers, chokes, motors, and electromagnet experiments. The thin enamel coating insulates each wire, allowing tight coil windings without short cir...

SKU: SF-COM-11289 | Brand: SparkFun

These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up.These hea...

SKU: AF-3119 | Brand: Adafruit

This HDMI plug breakout board lets you create custom HDMI cables or tap into individual HDMI pins for specialised wiring setups. The solid PCB features an HDMI plug with through-hole pads for soldering your own connec...

SKU: AF-3122 | Brand: Adafruit

Make your own custom DE-9 cable or DE-9 interface with ease, using this DE-9 Socket to Terminal Block Breakout. You get a nice solid PCB with an DE-9 socket and two strips of terminal blocks that you can use with stra...

SKU: SF-COM-11155 | Brand: SparkFun

These panel-mounting rocker switches have built-in indicator lights to let you know when your switch is engaged. They mount into a 20.2mm diameter hole and are rated up to 16A @ 12v. These simple SPST on-off switches ...

SKU: AF-3145 | Brand: Adafruit

A pack of 50 small single-row wire housings for building custom jumper cable harnesses. Compatible with both male and female crimp pins, these housings let you create exactly the wire configurations your project needs...

SKU: AF-3146 | Brand: Adafruit

Create custom wire harnesses with these single-row housings for DIY jumper cables. Compatible with both male and female jumper wires, these housings give you full control over your wiring layout and connector configur...

SKU: AF-3101 | Brand: Adafruit

Put your project in stealth mode with these silent Soft Tactile Switch Buttons.  Tactile switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless b...

SKU: AF-371 | Brand: Adafruit

A 150mm (6″) IDC ribbon cable with 6-pin (2×3) socket connectors on both ends at 0.1″ × 0.1″ (2.54mm) spacing. Commonly used for AVR ISP programming connections and other 2×3 header interfaces. Key Features Socket-...

SKU: SF-PRT-13164 | Brand: SparkFun

This is a simple three wire cable. Each cable is 6" long and is great for jumping from board to board or just about anything else. There is a 3-pin JST connector with 0.1" spacing on both ends. These jumper wires come...

SKU: AF-395 | Brand: Adafruit

An 8-channel bidirectional logic level converter breakout based on the TXB0108 chip. This converter automatically detects signal direction, eliminating the need for direction control pins. It shifts between virtually ...

SKU: AF-3111 | Brand: Adafruit

This is a box of six 25ft spools of stranded-core wire. Stranded-core wire is best used for wiring jigs where there's bending or movement expected. It also works well with terminal blocks. It's no...

SKU: SF-PRT-13126 | Brand: SparkFun

This female barrel jack plug is great for adding a common connector to the end of wires. This jack is compatible with 5.5x2.1mm barrel connectors. The outer shell unscrews to reveal solder terminals and a crimp strain...