Prototyping & Wiring

SKU: AF-1131 | Brand: Adafruit

A 500 mm extension cable with a JST-PH 2-pin socket on one end and a matching plug on the other. The colour-coded wires make it easy to verify correct polarity. Compatible with JST-PH terminated battery packs includin...

SKU: AF-1178 | Brand: Adafruit

Rollin' rollin' rollin', you can now roll around smooth as silk with these radial bearings. Often referred to as "skate bearings" They're good for supporting a rotating rod or as a wheel hub. However, these are higher...

SKU: LB-LR0335-FG | Brand: Little Bird

This 5-metre length of EL wire (electroluminescent wire) glows a vibrant fluorescent green when powered by the included battery-operated inverter. EL wire is a flexible, phosphor-coated wire that produces a cool, even...

SKU: LB-LS1216 | Brand: Little Bird

This sensor is composed of an infrared emitter on one upright and a shielded infrared detector on the other. By emitting a beam of infrared light from one upright to the other, the sensor can detect when an object pas...

SKU: AF-4007 | Brand: Adafruit

If you're like me, you've dreamed of being a dolphin - smoothly gliding through the water. Using your echo-location abilities to detect tasty fish treats. Until genetic modifications catches up with our desires, we'll...

SKU: AF-4031 | Brand: Adafruit

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack so you get left and right channels as well as a ground pin. You can use any 3.5mm stereo cable with this jac...

SKU: LB-LS0070 | Brand: Little Bird

The knob is designed to set directly on the potentiometer's ridges so it's an easy & secure fit. It has a nice feel, with a solid grip, tweaking it is quite fulfilling This is the red version and it has a nice deep...

SKU: SS-103030195 | Brand: Seeed Studio

Connect a micro:bit to the Grove ecosystem with this plug-and-play extension board from Seeed Studio. Its four onboard Grove ports make it easier to add modules such as sensors, actuators, communication devices and di...

SKU: AF-1669 | Brand: Adafruit

Listen up! This set of two 2.8" x 1.2" speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclos...

SKU: AF-1663 | Brand: Adafruit

A matching pair of 3-pin JST SM connector cables — one plug and one receptacle — for creating quick-connect/disconnect points in 3-wire circuits. The locking latch keeps the connection secure while still allowing easy...

SKU: AF-2195 | Brand: Adafruit

A 10-pack of 10µF 50V electrolytic capacitors with long, flexible leads that make them easy to use on breadboards and perfboard. Each capacitor has clear labelling on the body for quick identification. Electrolytic c...

SKU: AF-2193 | Brand: Adafruit

A 10-pack of 100µF 16V electrolytic capacitors with long, flexible leads that make them easy to use on breadboards and perfboard. Each capacitor has clear labelling on the body for quick identification. Electrolytic ...

SKU: AF-2166 | Brand: Adafruit

A low-dropout (LDO) 3.3 V linear voltage regulator based on the ST L4931 in a TO-92 package. With just 0.4 V dropout, it delivers a clean, regulated 3.3 V output from input voltages as low as 3.7 V — well suited for s...

SKU: AF-2324 | Brand: Adafruit

The Adafruit Ultimate GPS HAT adds high-quality GPS and GLONASS positioning to your Raspberry Pi. Built around a PA1616D module, it provides precise location data and a built-in real-time clock (RTC) with coin cell ba...

SKU: AF-2430 | Brand: Adafruit

Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the dozen for making programming and testing jigs but they're handy also i...

SKU: DF-FIT0085 | Brand: DFRobot

This custom-designed plastic wheel has a rubber tire measuring 1.65" (42 mm) in diameter and is designed to fit the output shafts on our mini metal gearmotors as well as the Solarbotics metal gear motors. Teeth on...

SKU: DF-SEN0032 | Brand: DFRobot

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos ...

SKU: DF-FIT0121 | Brand: DFRobot

Jumper wires are one of the most important gear component for the tinkerer. Often underestimated, but one of the first things to miss. If you are starting to assemble your tinker gear and wondering if this is really n...

SKU: AF-2717 | Brand: Adafruit

The TCA9548A 1-to-8 I2C multiplexer solves the common problem of needing multiple I2C devices with the same address on a single bus. It acts as a gatekeeper, routing I2C traffic to any of its eight downstream channels...

SKU: SF-BOB-09056 | Brand: SparkFun

A breakout board for the CD74HC4067 16-channel analogue/digital multiplexer/demultiplexer. This IC internally routes a common signal pin (SIG) to one of 16 channel pins, working with both analogue and digital signals ...