Prototyping & Wiring

SKU: SF-PRT-10898 | Brand: SparkFun

A pack of 100 premium female-to-female jumper wires, 155 mm long. Use these to connect any male header to another male header on breadboards, development boards, and breakout modules. Multiple jumpers can be installed...

SKU: AF-3296 | Brand: Adafruit

The Adafruit DS1307 Real Time Clock breakout keeps accurate time even when your microcontroller loses power or is reprogrammed. This battery-backed I2C RTC is one of the most widely used clock chips, making it a relia...

SKU: DF-DFR0342 | Brand: DFRobot

W5500 Ethernet with POE Mainboard is a new member in our Ethernet family. It is based on the ATmega32u4 and W5500 Ethernet chip, which is quite useful to most IOT projects. W5500 chip is a Hardwired TCP/IP embedded E...

SKU: SF-CAB-10649 | Brand: SparkFun

A 3-foot (approximately 90 cm) length of 10-wire ribbon cable. Useful for making clean, organised multi-conductor connections in electronics projects — ideal for connecting to IDC crimp-on connectors. Specifications ...

SKU: SF-COM-10634 | Brand: SparkFun

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow.

SKU: AF-3317 | Brand: Adafruit

The Adafruit VL53L0X is a Time-of-Flight (ToF) distance sensor from ST that uses an invisible laser to measure distances from approximately 50 mm to 1200 mm. By timing how long the laser light takes to bounce back, it...

SKU: AF-589 | Brand: Adafruit

A value pack of three Adafruit Perma-Proto Quarter-Sized Breadboard PCBs. Each board mirrors the layout of a tiny solderless breadboard (plus power rails) with 5-hole connected pads, four power bus rails, and clear si...

SKU: SF-COM-10349 | Brand: SparkFun

The FQP27P06 is a P-channel enhancement-mode power MOSFET rated for −60V and −27A. With a very low on-resistance of 70 mΩ and a gate threshold compatible with 5V logic, it is well suited for high-side switching contro...

SKU: AF-1831 | Brand: Adafruit

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 100K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will...

SKU: AF-1891 | Brand: Adafruit

Listen up! This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W of power. The speakers are rated at 0.25W, with a maximum input of 0.5W (pr...

SKU: AF-641 | Brand: Adafruit

A 3-ply conductive thread made entirely from 316L stainless steel fibre. Thin enough to sew by hand with a medium-eye needle, yet strong and smooth — ideal for wearable electronics, e-textile projects, and sewable cir...

SKU: SF-TOL-10243 | Brand: SparkFun

We don’t want to hype this solder TOO much, but this could possibly be the best solder in the world. There, we’ve said it. This is a special blend made specifically for us and we love it. It all started as a quest to ...

SKU: SF-TOL-10242 | Brand: SparkFun

We don’t want to hype this solder TOO much, but this could possibly be the best solder in the world. There, we’ve said it. This is a special blend made specifically for us and we love it. It all started as a quest ...

SKU: DF-DFR0406 | Brand: DFRobot

INTRODUCTION The Arduino Motor Shield is based on L298 (a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors). It helps you drive two...

SKU: SF-BOB-12700 | Brand: SparkFun

This simple breakout board routes a female USB Type-A connector's VCC, GND, D−, and D+ pins to a standard 0.1″ pitch header. It saves you the hassle of soldering tiny SMD connectors when adding USB host or device conn...

SKU: AF-3203 | Brand: Adafruit

The Adafruit Perma-Proto Bonnet Mini Kit is a prototyping daughter board sized for the Raspberry Pi Zero. It plugs directly onto the Pi's 2×20 GPIO header and provides a grid of 0.1″ soldering holes connected in a fam...

SKU: SF-BOB-10031 | Brand: SparkFun

We have no idea what USB device you are hooking up to, but if you want to access the microUSB port on something, you might want this. We broke out all 5 pins with a vertical microUSB connector for your prototyping nee...

SKU: AF-1982 | Brand: Adafruit

The Adafruit MPR121 Capacitive Touch Sensor Breakout provides 12 channels of capacitive touch sensing over I2C. The MPR121 handles all the capacitive filtering internally and can be configured for varying sensitivity ...

SKU: SF-COM-09772 | Brand: SparkFun

A standard 5 × 20 mm glass cartridge fuse rated at 5A / 125V AC. When current exceeds 5A, the internal filament breaks and opens the circuit, protecting your electronics from overcurrent damage. Compatible with standa...

SKU: DF-FIT0011 | Brand: DFRobot

INTRODUCTION The digital sensor cables are especially designed for our popular IO Expansion shield and sensors. It connects most of our digital sensor to the IO board. This price inclu...