Prototyping & Wiring

SKU: SF-COM-14567 | Brand: SparkFun

It’s tiny, it’s handy, and it can give your normal USB-equipped device a micro-B connector! With the USB to Micro-B Adapter you can make a flash drive connect to your tablet, connect a keyboard to your phone in order ...

SKU: AF-1620 | Brand: Adafruit

Add a power switch to any USB-powered project simply by plugging this between the USB power port and the USB cable. This is the most useful thing you never knew you needed! You'll want to pick up a bunch for your elec...

SKU: AF-1608 | Brand: Adafruit

The Adafruit Perma-Proto Quarter-Sized Breadboard PCB mirrors the layout of a tiny solderless breadboard with power rails, making it simple to transfer small prototyped circuits to a permanent soldered board. The comp...

SKU: SF-DEV-14459 | Brand: SparkFun

The SparkFun Qwiic HAT for Raspberry Pi is the quickest and easiest way to enter into SparkFun’s Qwiic ecosystem while still using that Raspberry Pi that you’ve come to know and love. The Qwiic HAT connects the I2C b...

SKU: AF-2005 | Brand: Adafruit

Silicone-sheathing wire is super-flexible and soft, and its also strong! Able to handle up to 200°C and up to 600V, it will do when PVC covered wire wimps out. We like this wire for being extremely supple and flexible...

SKU: AF-1789 | Brand: Adafruit

This 1K potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 1K ohm potentiometer, with a grippy shaft. Its smooth and easy to turn, but not so loose that it will ...

SKU: AF-1863 | Brand: Adafruit

This switched JST connector is the best way to quickly prototype with our LiPoly batteries. We paired a genuine JST connector with a slide switch that can do up to 600mA. Both are soldered onto a breadboard-friendl...

SKU: AF-1875 | Brand: Adafruit

Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V de...

SKU: AF-2222 | Brand: Adafruit

Connect your own PCB to a Raspberry Pi B+ with this normal-height female header.  The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has 3m...

SKU: AF-2201 | Brand: Adafruit

This is just about the cutest, tiniest little micro servo we could find, even smaller than the 9 gram micro servos we love so much.  It can rotate approximately 180 degrees (90 in each direction) and works just l...

SKU: AF-2187 | Brand: Adafruit

A custom-made 2×20 short female header designed for surface-mount (SMT) Raspberry Pi HAT designs. This header provides the slimmest possible profile when you need a low-clearance connection between your HAT and a Rasp...

SKU: AF-2168 | Brand: Adafruit

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to that s...

SKU: AF-2476 | Brand: Adafruit

Replacement silicone tubes for the Professional Silicone-Tip Solder Sucker. Cut to your desired length as needed — the elastic, heat-resistant silicone withstands temperatures up to 350°C, letting you get close to you...

SKU: AF-2473 | Brand: Adafruit

A 50 g spool of lead-free solder wire ideal for through-hole and surface-mount soldering. With a 0.5 mm diameter and no-clean rosin flux core, this wire delivers clean, reliable joints without the need for post-solder...

SKU: SF-PRT-14311 | Brand: SparkFun

These headers are made to work with the SparkFun ESP32 Thing and ESP32 Power Control Shield boards. Each set of headers makes your ESP32 Thing easily stackable with the Power Control Shield or other applications. This...

SKU: DF-DFR0201 | Brand: DFRobot

The Arduino Leonardo is a microcontroller board based on the ATmega32U4, offering the same flash, RAM, and capabilities as the ATmega328 found in the Uno. The key difference is built-in USB communication, allowing the...

SKU: SF-PRT-09139 | Brand: SparkFun

This is a SparkFun exclusive! These are 155mm long jumpers terminated as male to female. Use these to jumper from any male or female header on any board. Multiple jumpers can be installed next to one another on a 0.1"...

SKU: DF-FIT0225 | Brand: DFRobot

A comprehensive mounting kit containing a variety of M3 nylon and copper standoffs, screws, and nuts — all organised in an adjustable 24-compartment parts box. Everything you need to mount circuit boards, build robot ...

SKU: SF-COM-08862 | Brand: SparkFun

Huge 10mm through-hole LEDs. Mood light an entire wall! Features: 625-630nm Red 2.1-2.3VDC Forward Voltage 80mA Forward Current 30 degree viewing angle 10,000-12,000 MCD output Documents: Datasheet LED Tutorial

SKU: SF-COM-08720 | Brand: SparkFun

A miniature surface-mount momentary pushbutton switch with a low-profile design. Ideal for use as a tactile reset button or general-purpose input on custom PCBs. Rated up to 50 mA. Key Features Surface Mount (SMD) ...