Prototyping & Wiring

SKU: SF-WRL-12861 | Brand: SparkFun

This is a basic SMA (Sub-Miniature A) male to female connector cable. Each cable is 25cm (9.8") long and has a 50Ω impedance that can handle frequencies up to 17 GHz. The SMA connectors at each end are small enough...

SKU: SF-BOB-10467 | Brand: SparkFun

This simple breakout board makes it easy to use our LED tactile switches in a breadboard, or your next project. Note: Populate the board according to the polarity of the LED on the switch. The markings for the swi...

SKU: SF-PRT-10461 | Brand: SparkFun

These nylon standoffs are 3/8" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. Each standoff has an outer diameter of 6mm. Sold in pack...

SKU: AF-50 | Brand: Adafruit

We sure love the ATmega328 here at Adafruit, and we use them a lot for our own projects. The processor has plenty of GPIO, Analog inputs, hardware UART SPI and I2C, timers and PWM galore - just enough for most...

SKU: SF-COM-10443 | Brand: SparkFun

This is a simple LED-illuminated tactile button with a clear cap. It’s just like a basic tactile button, but it lights up blue! So now you can get visual feedback, or light up your project. These have a 12mm body a...

SKU: SF-PRT-10452 | Brand: SparkFun

Standard Philips-head 4-40 screws. They are ½" long and come in packs of ten. This is the screw size we use in most of the holes for our breakout boards. Check below for other associated hardware.

SKU: SF-COM-10442 | Brand: SparkFun

A tactile push button with a built-in red LED, combining momentary switching with visual feedback in a single component. Press the button and it lights up red — ideal for control panels, interactive projects, and anyw...

SKU: SF-COM-10440 | Brand: SparkFun

This is a simple LED-illuminated tactile button with a green cap. It’s just like a basic tactile button, but it lights up green! So now you can get visual feedback, or light up your project. These have a 12mm body and...

SKU: SF-COM-10439 | Brand: SparkFun

This is a simple LED-illuminated tactile button with a clear cap. It’s just like a basic tactile button, but it lights up white! So now you can get visual feedback, or light up your project. These have a 12mm body and...

SKU: AF-3347 | Brand: Adafruit

A pack of 10 tactile push buttons with a polished metal ball actuator, giving them a distinctive industrial look. The rounded top also makes them forgiving when pressed at an angle — useful for mechanical actuator set...

SKU: SF-SEN-12787 | Brand: SparkFun

This is the SparkFun RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and color measuring, proximity detection, and touchless gesture sensing. With this RGB and...

SKU: AF-3307 | Brand: Adafruit

Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic green protective casing, and a green LED at the tip of the switch, this Green LED Toggle Switch is sure&nb...

SKU: DF-FIT0455-Y | Brand: DFRobot

INTRODUCTION Comes in your choice of red, green, blue, yellow or white. This button locks and lights up when pushed. It's perfect for DIY projects which require a button and it's easy to mou...

SKU: SF-WIG-12772 | Brand: SparkFun

The SparkFun Logomatic v2 is a versatile serial and analogue data logger built around the NXP LPC2148 ARM7 microcontroller. It logs data to a microSD card in FAT32 format and appears as a USB mass storage device, so l...

SKU: DF-FIT0455-R | Brand: DFRobot

INTRODUCTION Comes in your choice of red, green, blue, yellow or white. This button locks and lights up when pushed. It's perfect for DIY projects which require a button and it's easy to mou...

SKU: DF-FIT0455-W | Brand: DFRobot

A self-locking illuminated push button with a white LED indicator. When pressed, the button locks into position and the LED lights up; press again to release. The built-in LED includes a resistor for direct 5–12V oper...

SKU: AF-618 | Brand: Adafruit

A compact 1.8" TFT display with true 18-bit colour (262,144 shades) and 160 × 128 resolution. It uses a simple SPI interface requiring only 4–5 digital pins and features two white LED backlights running on 3.3 V. Driv...

SKU: DF-FIT0455-B | Brand: DFRobot

INTRODUCTION Comes in your choice of red, green, blue, yellow or white. This button locks and lights up when pushed. It's perfect for DIY projects which require a button and it's easy to mou...

SKU: SF-PRT-12748 | Brand: SparkFun

A standard SMD (surface-mount) DC barrel power jack for use with common DC wall adapters. This is the same connector size used on most Arduino boards and many other development platforms. Key Features Surface-Mount...

SKU: SF-BOB-12731 | Brand: SparkFun

This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPR...