Prototyping & Wiring

SKU: AF-4302 | Brand: Adafruit

The official Raspberry Pi Micro HDMI to Standard HDMI cable features quality overmoulding with the Pi logo and moulded grips for easy installation. At 1 metre long, it's the perfect length for desktop setups with the ...

SKU: AF-4218 | Brand: Adafruit

If you need to add a panel-mount connection but don't have the time or ability to cut a custom oval or square hole, this USB C Round Panel Mount Extension Cable is the easiest and fastest way to panel-ify your project...

SKU: AF-4175 | Brand: Adafruit

As technology changes and adapts, so does Adafruit, and speaking of adapting, this adapter has a USB A plug and a USB C socket so your older computer or laptop can catch up to the latest USB Type C.USB C is the latest...

SKU: AF-3894 | Brand: Adafruit

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" female header sockets on the end. We're carrying these to match up with our Hallowing, for extending and conn...

SKU: SF-WRL-14876 | Brand: SparkFun

A 1/2-wave 915MHz LoRa duck antenna with 2dBi gain and an RP-SMA connector. Designed for the 860–960MHz band, this 200mm antenna is ideal for extending the range of LoRa nodes and other sub-GHz radio modules. Specifi...

SKU: EC-RPA00273R | Brand: Elecrow

This handy Three Wire Display Stand is made for Raspberry Pi, but also can adapt to other tablet PC, such as iPad. It is great for general electronics & TFT holding. You can adjust the angle as you like. Features ...

SKU: SF-WRL-15126 | Brand: SparkFun

After years of popularity with the XBee Series 1 and XBee Series 2, we now have the XBee Series 3 which brings the best of both worlds. XBee 3 not only handles 802.15.4, and ZigBee, but also BLE protocols and you can ...

SKU: DF-DFR0576 | Brand: DFRobot

The Gravity I2C Multiplexer solves address conflicts when you need to connect multiple I²C devices that share the same fixed address. It provides eight independent I²C ports on a single bus, allowing up to eight ident...

SKU: DF-FIT0603 | Brand: DFRobot

A transparent ABS case designed specifically for the Arduino UNO R3. The case protects your board from dust, splashes, and accidental short circuits while keeping all GPIO pins accessible through dedicated slots. The ...

SKU: SF-DEV-15123 | Brand: SparkFun

The SparkFun RedBoard Qwiic is an Arduino-compatible development board in the UNO R3 form factor with a built-in Qwiic connector for solderless I2C hookup. It programs over USB Micro-B using the Arduino IDE — select "...

SKU: SF-COM-15105 | Brand: SparkFun

This diode-transistor photocouplers consist of an LED, optically coupled to a high speed photodetector to transmit electrical signals between circuits while still isolating your system from higher voltages. The 6N137 ...

SKU: AF-1385 | Brand: Adafruit

Your power supply problems just got SOLVED! This little circuit board may look tiny but inside is a high efficiency DC/DC step-down converter which can output up to 3 Amp at 5V without the need of any heat-sink or for...

SKU: AF-1387 | Brand: Adafruit

Build custom USB connections without slicing apart a cable and soldering those thin internal wires. This DIY USB shell gives you a proper Type A male plug connector with easy-to-solder tabs and a two-part snap-togethe...

SKU: SF-BOB-15100 | Brand: SparkFun

Add a USB-C connector to your project without wrestling with tiny SMD pads. This breakout board routes the USB-C connector's key pins to a standard 0.1" pitch header, making it straightforward to integrate into breadb...

SKU: SF-COM-14978 | Brand: SparkFun

This little round on/off/on toggle switch is rated up to 10A at 125VAC and can be panel mounted in a 20mm diameter hole. It’ll also look pretty slick in your project!

SKU: AF-3642 | Brand: Adafruit

A 2.1 mm DC barrel jack with a built-in slide switch, giving you simple on/off control for devices that lack a dedicated power switch. It shares the same PCB footprint as a standard non-switched barrel jack, so it dro...

SKU: AF-2164 | Brand: Adafruit

The classic L7805 linear voltage regulator in a TO-220 package, capable of delivering a clean, regulated 5.0 V output (±2%) from an input voltage of 7–35 V. With built-in current limiting and thermal shutdown protecti...

SKU: AF-2448 | Brand: Adafruit

The Adafruit TB6612 Breakout is a compact dual H-bridge motor driver that can spin two DC motors bidirectionally, step one bipolar or unipolar stepper, or fire two solenoids — all at up to 1.2A continuous per channel ...

SKU: AF-2472 | Brand: Adafruit

The Adafruit BNO055 breakout delivers complete 9-DOF orientation sensing with onboard sensor fusion — no complex algorithms to write yourself. The Bosch BNO055 combines an accelerometer, gyroscope, and magnetometer on...

SKU: DF-FIT0216 | Brand: DFRobot

A compact, spring-loaded desoldering pump (solder sucker) for removing solder from PCB joints and through-holes. The ProsKit DP-366D features a double oil-sealed piston for guaranteed leak-free suction and a soft foam...