Prototyping & Wiring

SKU: AF-2458 | Brand: Adafruit

Doesn't this fixture clamp look like a character in a Pixar movie?  If you just drew two little eyes on it then you could just imagine it hopping around on nifty, adorable little adventures that ar...

SKU: DF-SEN0005 | Brand: DFRobot

This low cost SFR02 ultrasonic ranger has both I2C and Serial interfaces. New AutoTune algorithms intelligently back the minimum range right up to the transducer ringdown for the very best performance possible, aut...

SKU: AF-2459 | Brand: Adafruit

*Ka-thunk* Pin down that PCB with our Toggle Clamp, a sturdy and reliable way to quickly press and release with precision! A pogo-pin bed is a great way to connect and test boards without any soldering, but yo...

SKU: AF-2456 | Brand: Adafruit

This medium flip-up toggle clamp provides a quick, reliable way to press and hold PCBs firmly in place during testing, soldering, or pogo-pin bed operations. The rounded rubber tip grips securely without marring or da...

SKU: DF-DFR0108 | Brand: DFRobot

The Arduino Mega 2560 Rev3 is a microcontroller board based on the ATmega2560, offering significantly more I/O than standard Arduino boards. With 54 digital I/O pins, 16 analog inputs, and 4 hardware serial ports, it'...

SKU: DF-SEN0008 | Brand: DFRobot

This small sonar ranger from Devantech offers an amazing wide range from 3cm to 6m. The SRF10 is interfaced using the IIC bus. SPECIFICATIONS Voltage-5v Current-15mA Typ. 3mA Standby Frequenc...

SKU: DF-FIT0101 | Brand: DFRobot

This is a really easy use prototyping plate. Basically you can put everything from Arduino board to sensors, even a motor on top of it. It fits M2-M3 screws. NOTE: This product does not ship with the board shown abov...

SKU: AF-2460 | Brand: Adafruit

An ultra-compact passive GPS antenna measuring just 9 × 9 × 6.5 mm, with a 50 mm uFL cable. Ideal for space-constrained projects where a full-size antenna won't fit. Key Features Tiny Form Factor – Only 9 × 9 × 6.5...

SKU: DF-SEN0233 | Brand: DFRobot

A multifunction air quality monitor that measures particulate matter (PM2.5), formaldehyde concentration, temperature, and humidity. It uses laser scattering to detect suspended particles in the air, an electrochemica...

SKU: DF-DFR0117 | Brand: DFRobot

Arduino has a small amount of data storage space, The Arduino UNO has 32k. It doesn't have enough space if you want to store a lot of data. Therefore, we need to add an EEPROM Data Storage Module to increase its stora...

SKU: DF-SEN0080 | Brand: DFRobot

The XL-MaxSonar-WR sensor provides very short to long-range detection and ranging, in a compact, robust PVC housing, designed to meet IP67 water intrusion, and matches standard electrical 3/4" PCV pipe fittings....

SKU: AF-2571 | Brand: Adafruit

This 50-pin FPC extension board lets you add approximately 22cm of reach to any 50-pin, 0.5mm pitch FPC/FFC connection. The board features two 50-pin flex connectors with a 200mm (20cm) FPC cable included, giving a to...

SKU: DF-TEL0020 | Brand: DFRobot

This is the XBee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. Th...

SKU: DF-DFR0031-Y | Brand: DFRobot

The Digital Piranha LED Module (Yellow) is a bright LED module designed for Arduino and compatible microcontroller boards. Control it via a digital pin (LOW = on, HIGH = off) or use PWM output to adjust brightness for...

SKU: AF-2633 | Brand: Adafruit

The Adafruit Bluefruit LE SPI Friend adds Bluetooth Low Energy connectivity to any microcontroller with just 4–5 GPIO pins. Using SPI instead of UART means no baud rate configuration or flow control to worry about — c...

SKU: DF-FIT0139 | Brand: DFRobot

These nuts can be used to install your circuit boards, sensors and mechanical mountings. The wide flange at one end with an uneven surface eliminates the need for using extra washers to keep the nut tightly secur...

SKU: DF-FIT0147 | Brand: DFRobot

This is a 6-pin female header, with extra long legs -- great for stacking Arduino shields.Pins are spaced by 0.1". APPLICATIONS PCB Arduino Shield Header SPECIFICATIONS18.6 x 15.8 x 2.5(mm)(0.73x0.62x0.09") SHIPPING...

SKU: AF-2591 | Brand: Adafruit

I know you just did a double take when looking at this power supply, what's up with the two cables? Normally you have a switching power supply that plugs into the wall and provides something like 5V or 9V or 12V regul...

SKU: AF-2674 | Brand: Adafruit

If you've been diggin' our monochome OLEDs but need something bigger, this display will delight you. These displays are 2.7" diagonal, and very readable due to the high contrast of an OLED display. This display is mad...

SKU: DF-FIT0106 | Brand: DFRobot

A pack of ten 6-pin female headers with standard 0.1″ (2.54mm) pin spacing. Commonly used for Arduino shield connections and general prototyping. Key Features Standard 0.1″ Pitch – Compatible with breadboards, Ardu...