Prototyping & Wiring

SKU: SF-PRT-12711 | Brand: SparkFun

The SparkFun USB LiPoly Charger is a single-cell Li-Ion/Li-Polymer battery charging board based on the MCP73831T. It charges 3.7V LiPo cells at a selectable rate of 500 mA or 100 mA via a solder jumper, with power inp...

SKU: AF-1858 | Brand: Adafruit

This 2.2"/57mm long antenna has 2dBi of gain and 50Ω impedance so it will work fantastically with just about any 850/900/1800/1900/2100 wireless receiver/transmitter such as any Cellular or GSM/GPRS device. Anten...

SKU: AF-1897 | Brand: Adafruit

The Adafruit SPI Non-Volatile FRAM Breakout provides 64 Kbit (8 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no pa...

SKU: AF-1903 | Brand: Adafruit

The PowerBoost 500 Basic is a compact DC/DC boost converter that takes input from 1.8V or higher and outputs a steady 5.2V — perfect for powering portable 5V projects from batteries. The slightly elevated 5.2V output ...

SKU: SF-PRT-12699 | Brand: SparkFun

This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prot...

SKU: DF-DFR0411 | Brand: DFRobot

INTRODUCTION This DC motor has an integrated transistor built in to the board, eliminating the need for a motor driver. Use PWM to control it for all your DIY project needs. It uses the 3 pi...

SKU: AF-3428 | Brand: Adafruit

A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Even...

SKU: AF-680 | Brand: Adafruit

These 5mm diffused RGB LEDs feature a built-in controller chip that automatically cycles through colours in a fast flashing pattern — no microcontroller or programming required. With just two leads (power and ground),...

SKU: SF-CAB-10177 | Brand: SparkFun

You might have seen these cables used in computers. They are typically used to bring USB connections from a motherboard to the external case, or the rear expansion slots. They have a 0.1" spaced 4-pin header on one en...

SKU: AF-1901 | Brand: Adafruit

A Qi-compatible wireless charging receiver module that outputs regulated 5 V at up to 500 mA. Place this module on any standard Qi charging base to receive power wirelessly — ideal for adding wireless recharging capab...

SKU: SF-SEN-12642 | Brand: SparkFun

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of so...

SKU: SF-BOB-10160 | Brand: SparkFun

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. Th...

SKU: DF-FIT0425 | Brand: DFRobot

The ECell Breadboard-Plugin LED pack contains 8 colour-coded LEDs mounted on gold-plated breadboard-compatible modules. Each module has clearly marked polarity and circuit symbols, making it easy to identify component...

SKU: DF-FIT0423 | Brand: DFRobot

INTRODUCTION Introducing "The Breadboard-Plugin Kit" - the first kit in the ECell series. The Breadboard-Plugin Kit provides a range of common components such as resistors, capacitors,...

SKU: SF-SEN-10127 | Brand: SparkFun

This is a basic RFID tag that functions within the MIFARE Classic® 1K guidelines. You can use these for all sorts of identification and sensing applications. The tag also has 1K of data storage which can be read and w...

SKU: AF-705 | Brand: Adafruit

A compact 3-wire voltage meter with a vivid green 3-digit 7-segment display. Reads 0–99.9VDC with 0.1V precision, making it perfect for monitoring battery levels, power supplies, and electronic projects. Mounting tabs...

SKU: SF-BOB-10124 | Brand: SparkFun

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can re...

SKU: AF-706 | Brand: Adafruit

These extra-long stacking headers are designed for BeagleBone Capes, allowing you to stack multiple capes on a single BeagleBone for modular, expandable designs. They work just like standard 2×23 0.1"-spaced female he...

SKU: AF-1918 | Brand: Adafruit

An analog UV light sensor breakout based on the GUVA-S12SD photodiode, detecting the 240–370nm range covering UVB and most of the UVA spectrum. An on-board op-amp amplifies the tiny photodiode current to a readable vo...

SKU: AF-1923 | Brand: Adafruit

A 10-segment LED bar graph display in yellow-green. At just 1" (25mm) long, it's compact enough to plug directly into a breadboard while remaining clearly visible. The diffused rectangular lenses give a clean, even gl...