Prototyping & Wiring

SKU: SF-PRT-10372 | Brand: SparkFun

This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers...

SKU: AF-1827 | Brand: Adafruit

Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. This is the 'slim' version of the DIY USB-A Male connector. It's a little more elegant because instead of snapp...

SKU: AF-1813 | Brand: Adafruit

A 10-segment LED bar graph display in a warm amber colour. At just 1" (25mm) long, it's compact enough to plug directly into a breadboard while remaining clearly visible. The diffused rectangular lenses give a clean, ...

SKU: DF-KIT0098 | Brand: DFRobot

INTRODUCTION Breadboard-Plugin Components Pack is a new kit designed for breadboard experiment. It provides many kinds of components, such as resistors, capacitors, diodes, transistor .et...

SKU: SF-PRT-10361 | Brand: SparkFun

This is a simple six wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 6-pin JST SH connector on t...

SKU: SF-COM-12766 | Brand: SparkFun

The L7812 is a three-terminal positive voltage regulator with a fixed 12V output. It provides stable local regulation with built-in protection against overcurrent, thermal overload, and short circuits, making it a rel...

SKU: SF-PRT-10287 | Brand: SparkFun

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack...

SKU: SF-PRT-12711 | Brand: SparkFun

The SparkFun USB LiPoly Charger is a single-cell Li-Ion/Li-Polymer battery charging board based on the MCP73831T. It charges 3.7V LiPo cells at a selectable rate of 500 mA or 100 mA via a solder jumper, with power inp...

SKU: AF-1858 | Brand: Adafruit

This 2.2"/57mm long antenna has 2dBi of gain and 50Ω impedance so it will work fantastically with just about any 850/900/1800/1900/2100 wireless receiver/transmitter such as any Cellular or GSM/GPRS device. Anten...

SKU: AF-1897 | Brand: Adafruit

The Adafruit SPI Non-Volatile FRAM Breakout provides 64 Kbit (8 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no pa...

SKU: AF-1903 | Brand: Adafruit

The PowerBoost 500 Basic is a compact DC/DC boost converter that takes input from 1.8V or higher and outputs a steady 5.2V — perfect for powering portable 5V projects from batteries. The slightly elevated 5.2V output ...

SKU: SF-PRT-12699 | Brand: SparkFun

This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prot...

SKU: DF-DFR0411 | Brand: DFRobot

INTRODUCTION This DC motor has an integrated transistor built in to the board, eliminating the need for a motor driver. Use PWM to control it for all your DIY project needs. It uses the 3 pi...

SKU: AF-3428 | Brand: Adafruit

A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Even...

SKU: AF-680 | Brand: Adafruit

These 5mm diffused RGB LEDs feature a built-in controller chip that automatically cycles through colours in a fast flashing pattern — no microcontroller or programming required. With just two leads (power and ground),...

SKU: SF-CAB-10177 | Brand: SparkFun

You might have seen these cables used in computers. They are typically used to bring USB connections from a motherboard to the external case, or the rear expansion slots. They have a 0.1" spaced 4-pin header on one en...

SKU: AF-1901 | Brand: Adafruit

A Qi-compatible wireless charging receiver module that outputs regulated 5 V at up to 500 mA. Place this module on any standard Qi charging base to receive power wirelessly — ideal for adding wireless recharging capab...

SKU: SF-SEN-12642 | Brand: SparkFun

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of so...

SKU: SF-BOB-10160 | Brand: SparkFun

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. Th...

SKU: DF-FIT0425 | Brand: DFRobot

The ECell Breadboard-Plugin LED pack contains 8 colour-coded LEDs mounted on gold-plated breadboard-compatible modules. Each module has clearly marked polarity and circuit symbols, making it easy to identify component...