Prototyping & Wiring

SKU: PL-1634 | Brand: Pololu

The MQ-3 is a semiconductor gas sensor that detects alcohol vapour at concentrations from 0.04 mg/L to 4 mg/L — a range suitable for building a breathalyser. It provides a simple analog voltage output that requires on...

SKU: DF-FIT0099 | Brand: DFRobot

A prototyping board is one of the main steps in hardware development, also called a perf board. Breadboard, wiring and punching in chips, resistors and leds is probably the first step. While this is good to confirm a...

SKU: PL-2510 | Brand: Pololu

Overview A Zumo robot preparing to attack a Parallax SumoBot. Zumo Robot for Arduino, v1.2. This Zumo robot is a low-profile tracked robot platform intended for use with an Arduino (or compatible device, such...

SKU: DF-FIT0108 | Brand: DFRobot

A solder-tail DB9 male connector for serial communication interfaces including RS-232, RS-422, and RS-485. This is one of the most widely used connectors for serial data links in industrial, embedded, and legacy compu...

SKU: PL-2490 | Brand: Pololu

This sensor is a carrier/breakout board for ST’s VL53L0X laser-ranging sensor, which measures the range to a target object up to 2 m away. The VL53L0X uses time-of-flight measurements of infrared pulses for rangi...

SKU: DF-FIT0140 | Brand: DFRobot

These are two pin jumpers (also called shunts) that will create an electrical connection for the 2.54mm(0.1") male pin headers. Commonly used to modify settings on a board or device. APPLICATIONS Jumpering pi...

SKU: DF-DFR0126 | Brand: DFRobot

This Audio Analyzer module features the MSGEQ7 graphic equalizer display filter.It will give your arduino ears. Sound is broken down into seven frequency bands and the peak level for each band can be read. The seven ...

SKU: DF-FIT0148 | Brand: DFRobot

This product includes 2-pin 2.0mm mating connector housing(10 units) and crimp pins (20 units). They work with wires ranging from 28 to 26 AWG. SPECIFICATIONS 2-pin 2.0mm mating connector housing 28-26 AWG crim...

SKU: SF-SEN-14348 | Brand: SparkFun

The SparkFun CCS811/BME280 Environmental Combo Breakout takes care of all your atmospheric-quality sensing needs with the popular CCS811 and BME280 ICs. This unique breakout provides a variety of environmental data, i...

SKU: PL-2463 | Brand: Pololu

The Vishay TSSP58P38 is a unique modulated IR receiver that is designed for IR brightness detection instead of data communication for remote control. This sensor can be used with a 38 kHz modulated IR emitter an...

SKU: SF-PRT-14322 | Brand: SparkFun

These stackable headers are made to work with the Particle Photon and Photon ProtoShield boards. Each header adds a great deal of connectivity to your next Photon project. Each order includes one 1x12 stackable header...

SKU: DF-FIT0008-G | Brand: DFRobot

This is a very small breadboard with 170 tie points. This bread board is compatible with the Arduino Proto Shield. Strong self-adhesive backing. Measures 1.8"x1.4".You also have choices of different colors. SP...

SKU: DF-DFR0164 | Brand: DFRobot

This is a new version of the FTDI breakout board features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The 8U2 firmware uses the standard USB COM drivers, and no ...

SKU: TB-ZS5086 | Brand: Little Bird

A 74LS86 quad 2-input exclusive-OR (XOR) gate IC in a through-hole DIP-14 package. Contains four independent 2-input XOR gates, essential for parity checking, arithmetic circuits, and data comparison. Key Features ...

SKU: SF-COM-09349 | Brand: SparkFun

This is a very simple, clear infrared LED. These devices operate between 940-950nm and work well for generic IR systems including remote control and touch-less object sensing. Pair them with any of our IR receivers (s...

SKU: DF-FIT0194 | Brand: DFRobot

A 10-pack of M3 × 30mm nylon standoffs with matching screws and nuts. Nylon standoffs are non-conductive, making them ideal for isolating circuit boards from metal chassis or other conductive surfaces without risking ...

SKU: SF-PRT-09280 | Brand: SparkFun

This is a 6-pin female header, with extra long legs – great for stacking Arduino shields. Pins are spaced by 0.1". Documents: Datasheet

SKU: AF-2743 | Brand: Adafruit

This adapter board is designed to make it easier to use ARM dev boards that use slimmer 2x5 (0.05"/1.27mm pitch) SWD cables for programming.  It's helpful for using products like the JTAGulator, STLink or SEGG...

SKU: SF-PRT-09194 | Brand: SparkFun

A mixed pack of 100 premium jumper wires in assorted colours, ideal for breadboard prototyping and connecting to 0.1″ headers. The pack includes 50 male-to-male and 50 female-to-female wires, each 155 mm (6″) long. T...

SKU: PL-1487 | Brand: Pololu

A compact 170-point solderless breadboard in black, perfect for small circuits and prototyping with DIP ICs. The 17-row layout accommodates up to two 14- or 16-pin DIP packages, making it ideal for quick test circuits...