Prototyping & Wiring

SKU: DF-SEN0186 | Brand: DFRobot

INTRODUCTION  Ever want to build your own weather station? This iot weather station kit includess anemometer, wind vane and rain bucket. The serial communication method provides good compatibility and ma...

SKU: SF-SEN-12784 | Brand: SparkFun

This is the SparkFun “Time-of-Flight” Range Finder, a breakout for the VL6180 distance sensor. Unlike most distance sensors that rely reflected light intensity or reflected angles to determine range, the VL6180 use...

SKU: SF-PRT-12791 | Brand: SparkFun

This is a 2x23 pin male PTH header. This piece is in the common configuration for Beaglebone Black headers that can be broken apart to form smaller header formations. Each pin has a spacing of 0.1" in between each oth...

SKU: SF-PRT-10359 | Brand: SparkFun

This is a simple four wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 4-pin JST SH connector on ...

SKU: SF-SEN-12728 | Brand: SparkFun

Infrared proximity sensor made by Sharp. Part # GP2Y0A41SK0F has an analog output that varies from 3.1V at 4cm to 0.3V at 30cm with a supply voltage between 4.5 and 5.5VDC. The sensor has a Japanese Solderless Termina...

SKU: SF-PRT-12718 | Brand: SparkFun

PCB mount clip to hold a AAA battery. Sold in single units, you’ll need two for each battery. These work great for small, low power applications that need a battery to run. Low cost and easy to use!Documents:Datasheet

SKU: SF-BOB-12708 | Brand: SparkFun

This is the SparkFun Real Time Clock (RTC) Module, this little breakout that uses the DS1307 to keep track of the current year, month, day as well as the current time. The module comes fully assembled and includes a s...

SKU: SF-ROB-12629 | Brand: SparkFun

The DAGU Wheel Encoder Kit is a simple add-on for wheeled robots that measures speed and distance travelled. Each kit includes two neodymium 8-pole magnets with rubber hubs and two hall-effect sensors, providing relia...

SKU: DF-FIT0475 | Brand: DFRobot

This plywood case is a solid enclosure for your LattePanda Windows 10 SBC. The case protects the board from ESD damage while letting you see status LEDs and providing access to USB, HDMI, SD card, GPIO and anten...

SKU: DF-SEN0002 | Brand: DFRobot

The URM04 Ultrasonic sensor is developed based upon our popular URM37 ultrasonic sensor, it is using RS485 interface which allows multiple sensors to be used simultaneously . The RS485 interface allows a number of...

SKU: DF-DFR0072 | Brand: DFRobot

At sometime or another you may run out of pins on your Arduino board and need to extend it with shift registers.  With this shift out module which is based on 74HC595. The datasheet refers to the 74HC595 as an "8...

SKU: SF-PRT-09387 | Brand: SparkFun

A pack of 10 premium male-to-male jumper wires, 12" (30cm) long. Compatible with breadboards, Arduino headers, and any 0.1" (2.54mm) pitch prototyping board. Assorted colours for easy circuit identification. Specific...

SKU: SF-PRT-09388 | Brand: SparkFun

This is a SparkFun exclusive! These are 12" long jumper wires terminated as male to male. Use these to jumper from any female header on any board. Multiple jumpers can be connected next to one another on a 0.1...

SKU: AF-2120 | Brand: Adafruit

If you've started designing your own PCBs in Eagle or KiCad and want to make your PCB a reality, you may start out with an etching system to pattern out traces. But that's only half the job! You'll also need a way ...