Prototyping & Wiring

SKU: SF-TOL-10602 | Brand: SparkFun

Precision curved tweezers with an ESD-safe coating, ideal for handling surface-mount components and other small electronic parts. The fine curved tip provides excellent control when placing or removing tiny components...

SKU: SF-PRT-10592 | Brand: SparkFun

This is the SMD version of PRT-07948, which is the unit we like to use as RTC backup and SRAM backup for GPS units. Holds battery in place with friction. The metal housing connects to the positive side of the batte...

SKU: SF-WRL-10533 | Brand: SparkFun

A simple 315 MHz wireless receiver module that pairs with 315 MHz transmitters to create a basic one-way data link. It fits easily into a breadboard and works well with microcontrollers like Arduino for straightforwar...

SKU: SF-COM-10468 | Brand: SparkFun

The MSGEQ7 is a CMOS graphic equaliser IC that divides the audio spectrum into seven frequency bands: 63 Hz, 160 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.25 kHz, and 16 kHz. Each band is peak-detected and multiplexed to provide ...

SKU: SF-PRT-10454 | Brand: SparkFun

Standard 4-40 zinc-plated hex nuts. A common thread size used in electronics enclosures, PCB mounting, and small hardware assemblies. Specifications Thread Size – 4-40 (UNC) Material – Zinc-plated steel Quantity ...

SKU: DF-FIT0452 | Brand: DFRobot

A 2-way lever-action wire connector made from flame-retardant material. These connectors provide a quick, solderless way to join wires — simply lift the lever, insert the stripped wire, and push the lever down to lock...

SKU: SF-COM-12766 | Brand: SparkFun

The L7812 is a three-terminal positive voltage regulator with a fixed 12V output. It provides stable local regulation with built-in protection against overcurrent, thermal overload, and short circuits, making it a rel...

SKU: SF-PRT-10287 | Brand: SparkFun

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack...

SKU: SF-PRT-12711 | Brand: SparkFun

The SparkFun USB LiPoly Charger is a single-cell Li-Ion/Li-Polymer battery charging board based on the MCP73831T. It charges 3.7V LiPo cells at a selectable rate of 500 mA or 100 mA via a solder jumper, with power inp...

SKU: AF-1858 | Brand: Adafruit

This 2.2"/57mm long antenna has 2dBi of gain and 50Ω impedance so it will work fantastically with just about any 850/900/1800/1900/2100 wireless receiver/transmitter such as any Cellular or GSM/GPRS device. Anten...

SKU: SF-BOB-10160 | Brand: SparkFun

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. Th...

SKU: DF-FIT0425 | Brand: DFRobot

The ECell Breadboard-Plugin LED pack contains 8 colour-coded LEDs mounted on gold-plated breadboard-compatible modules. Each module has clearly marked polarity and circuit symbols, making it easy to identify component...

SKU: SF-BOB-10124 | Brand: SparkFun

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can re...

SKU: AF-1918 | Brand: Adafruit

An analog UV light sensor breakout based on the GUVA-S12SD photodiode, detecting the 240–370nm range covering UVB and most of the UVA spectrum. An on-board op-amp amplifies the tiny photodiode current to a readable vo...

SKU: DF-FIT0480 | Brand: DFRobot

INTRODUCTION This High Speed HDMI Cable provides a one-cable solution for your home entertainment needs. As a versatile HDMI cable, it provides high-definition quality for not only LattePand...

SKU: SF-ROB-12567 | Brand: SparkFun

This buzzer is an add-on for your RedBot that gives your robot the ability to make awesome beep-boop noises or alerts when something interesting (or terrible) happens. The buzzer works by making use of two I/O pi...

SKU: SF-PRT-09915 | Brand: SparkFun

This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST connector on one end, bare cable on the opposite end. It also comes with the mating connector ...

SKU: SF-COM-09856 | Brand: SparkFun

A pack of 25 standard red 5 mm through-hole LEDs. Supplied in a reusable ESD-safe bag. Specifications Colour – Red Size – 5 mm through-hole Forward Voltage – ~1.8–2.2 V Forward Current – 20 mA Package Contents...

SKU: AF-780 | Brand: Adafruit

Need some indicators? We are big fans of these diffused blue LEDs, as featured in the LoL shield. They are really bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will ad...

SKU: SF-COM-09773 | Brand: SparkFun

This is a 5mm PTH fuse clip intended to be used with our Glass Fuses. Note: These are sold in single units. If you intend to secure a fuse using these clips you’ll need two clips. We recommend ordering two. Part #: ...