Prototyping & Wiring

SKU: AF-3642 | Brand: Adafruit

A 2.1 mm DC barrel jack with a built-in slide switch, giving you simple on/off control for devices that lack a dedicated power switch. It shares the same PCB footprint as a standard non-switched barrel jack, so it dro...

SKU: AF-2164 | Brand: Adafruit

The classic L7805 linear voltage regulator in a TO-220 package, capable of delivering a clean, regulated 5.0 V output (±2%) from an input voltage of 7–35 V. With built-in current limiting and thermal shutdown protecti...

SKU: AF-2448 | Brand: Adafruit

The Adafruit TB6612 Breakout is a compact dual H-bridge motor driver that can spin two DC motors bidirectionally, step one bipolar or unipolar stepper, or fire two solenoids — all at up to 1.2A continuous per channel ...

SKU: AF-2472 | Brand: Adafruit

The Adafruit BNO055 breakout delivers complete 9-DOF orientation sensing with onboard sensor fusion — no complex algorithms to write yourself. The Bosch BNO055 combines an accelerometer, gyroscope, and magnetometer on...

SKU: DF-FIT0216 | Brand: DFRobot

A compact, spring-loaded desoldering pump (solder sucker) for removing solder from PCB joints and through-holes. The ProsKit DP-366D features a double oil-sealed piston for guaranteed leak-free suction and a soft foam...

SKU: SF-COM-09117 | Brand: SparkFun

This is a 12-step rotary encoder with a nice ‘clicking’ feel. It’s breadboard friendly, and has a pretty handy select switch (by pushing in on the knob). The encoder is different from a potentiometer in that an enc...

SKU: DF-FIT0296 | Brand: DFRobot

A 150mm servo extension cable for reaching servos mounted further from the controller than the servo's built-in lead allows. Male connector plugs into the controller, female connector mates with the servo. Also works ...

SKU: SF-BOB-14021 | Brand: SparkFun

This is the SparkFun RJ11 Breakout, two simple breakout boards for the common 6-pin RJ11 connector. These little boards can easily have one of our RJ11 6-Pin Connectors to work with common telephone cables. Each bo...

SKU: DF-FIT0244 | Brand: DFRobot

A pack of 50 basic 3mm LEDs in five colours — 10 each of red, green, yellow, white, and blue. Handy for prototyping, indicator lights, and Arduino projects. Specifications Forward Voltage – 1.8–2.2V Max Current – ...

SKU: SF-PRT-08272 | Brand: SparkFun

This 2 mm pitch 10-pin socket mates with XBee radio modules from Digi, allowing you to mount your XBee without soldering it directly to a PCB. You'll need two of these sockets to connect to all 20 pins on an XBee modu...

SKU: DF-FIT0323 | Brand: DFRobot

An assortment pack of 100 through-hole diodes across 8 commonly used types. A handy selection to keep in your parts bin for prototyping, repairs, and project builds — covering signal diodes, rectifiers, fast-recovery ...

SKU: SF-COM-00533 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard red LED. The lens is 3mm in diameter, and is diffused.

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: AF-239 | Brand: Adafruit

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the powe...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: SF-COM-11372 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a blue lens. It has a typical forward voltage of 3.4V and ...

SKU: SF-COM-11121 | Brand: SparkFun

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow.Features: 3.0-3.4VDC Forward Voltage 20mA Forward Current 40 degree viewing angle 150-180 MCD output ...

SKU: SF-COM-12993 | Brand: SparkFun

This is an SMD 12mm square SPST button. What we really like is the large button head and good tactile feel (it ‘clicks’ really well). This button is great for user input or a good reset button on a PCB, heck, we use t...

SKU: SF-COM-12903 | Brand: SparkFun

Sometimes when you have too many choices, it’s hard to make a good decision. In fact, there are times when you just want a bag of LEDs, just one of each, that’s all you want. Well too bad, you are getting two of each!...

SKU: SF-PRT-10571 | Brand: SparkFun

These are simple 2-position screw terminals with 2.54mm pitch pins. Rated up to 150V @ 6A, this terminal can accept 30 to 18AWG wire. The 2.54mm pitch will line up with standard 0.1" perf boards.Documents: Datasheet