New Arrivals

SKU: AF-3464 | Brand: Adafruit

The Adafruit Joy Bonnet turns your Raspberry Pi Zero into a handheld gaming device. This fully assembled bonnet sits on top of any Pi Zero and provides arcade-style controls — a mini joystick and buttons — that act as...

SKU: SF-COM-10002 | Brand: SparkFun

Knobs are a great way to finish off your project and make it easier to adjust the level of your death ray. This knob mates to a 0.25" shaft. The knob slides onto the potentiometer and holds tightly with a strong frict...

SKU: AF-735 | Brand: Adafruit

An 8-bit logic level shifter in a breadboard-friendly DIP package. The 74LVC245 converts between 3.3V and 5V logic levels, making it easy to interface modern 3.3V sensors and peripherals with 5V microcontrollers like ...

SKU: AF-3413 | Brand: Adafruit

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need. They come in both male and female, and use crafty ...

SKU: DF-FIT0471 | Brand: DFRobot

INTRODUCTION This is a small DC - DC boost module that converts a 0.9 ~ 5v power source to standard 5V, making it capable of supplying power to an Arduino microcontroller and other small ...

SKU: AF-1894 | Brand: Adafruit

A 6" × 6" (152 × 152 mm) sheet of DuPont Pyralux flexible PCB material — the same material used to make flexible circuits in smartphones and consumer electronics. One side is 1 oz (35 µm) copper, and the other is 25 µ...

SKU: DF-SEN0211 | Brand: DFRobot

INTRODUCTION When you want to measure AC current it is impractical and hazardous to cut in to your live wiring. The analog AC current sensor developed by DFRobot is a good solution to this p...

SKU: DF-FIT0473 | Brand: DFRobot

This metal DC geared motor features a 45:1 metal gear reducer in a compact form factor, delivering up to 4.5 kg·cm of stall torque at 133 RPM. The all-metal gearbox provides durability and reliability for robotics, dr...

SKU: AF-760 | Brand: Adafruit

A 40-piece set of premium male-to-male jumper wires in a rainbow ribbon cable format. Each wire is 12″ (300mm) long with 0.1″ (2.54mm) male header contacts on both ends, fitting cleanly on standard-pitch headers and b...

SKU: DF-DFR0430 | Brand: DFRobot

INTRODUCTION An ordinary DC motor requires an H Bridge to work with a microcontroller such as an UNO. For newcomers to electronics, the process of finding the right motor driver, connecting it to the MCU and lear...

SKU: SF-PRT-09916 | Brand: SparkFun

This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST connector on one end, bare cable on the opposite end. It also comes with the mating connector f...

SKU: SF-DEV-09911 | Brand: SparkFun

A bare OBD-II connector for building custom automotive diagnostic tools and vehicle data interfaces. OBD-II (On-Board Diagnostics II) is a standardised diagnostic port found on most cars, providing access to engine co...

SKU: AF-778 | Brand: Adafruit

A pack of 25 diffused white 3 mm LEDs — bright enough to be visible in daylight and with a wide viewing angle thanks to the diffused lens. They fit easily into breadboards and are perfect for indicators, status lights...

SKU: DF-SEN0208 | Brand: DFRobot

Most ultrasonic distance sensors aren't waterproof which can be a problem if you need your project to withstand the elements outdoors. No need to worry any more! We have developed waterproof ultrasonic distance senso...

SKU: DF-SEN0197 | Brand: DFRobot

The Gravity Voice Recorder Module is a compact board with integrated record and playback functions, based on the ISD1820 chip. Simply press the record button, speak into the onboard microphone, and release to save up ...

SKU: AF-793 | Brand: Adafruit

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" female ...

SKU: AF-3429 | Brand: Adafruit

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a ...

SKU: AF-3430 | Brand: Adafruit

A 24 mm translucent red arcade button with built-in LEDs. The crystal-clear body glows when the LEDs are powered, making it ideal for illuminated control panels, arcade cabinets, and interactive projects. A pre-instal...

SKU: SF-PRT-09750 | Brand: SparkFun

A 3-pin right-angle JST PH series through-hole connector with 2mm pin spacing. These compact connectors provide a solid locking connection and are rated for moderate current, making them a reliable choice for PCB-moun...

SKU: DF-DFR0019 | Brand: DFRobot

This is the very first prototyping shield for Arduino in the market since 2010. It comes with prototyping area that you can sold led , switch or other components, it also comes with a mini Arduino breadboard that can...