New Arrivals

SKU: SF-TOL-16886 | Brand: SparkFun

Have you ever needed to power a project while in your car? Now you can without having to drag a computer along with this cost effective 5V, 2.4A USB car charger. These car chargers have a standard USB 'A' connector fo...

SKU: EC-CIA51002C | Brand: Elecrow

W5100 is a multifunctional Monolithic network interface chip, internal integrate a 10/100 Ethernet controller , it apply to a embedded system which is High-Integrate, high-stability, high-performance but low-cost. By ...

SKU: DF-FIT0668 | Brand: DFRobot

A versatile 2-in-1 USB cable with both USB-C and Micro USB connectors on one end, so you can charge and program devices with either interface using a single cable. The flat cable design resists tangling, and the inclu...

SKU: AF-4763 | Brand: Adafruit

These little chips are like miniature SSD drives for your electronics. When you don't need something with as much storage as a micro SD card, but an EEPROM is too small, SPI (or QSPI) Flash chips give you on-the-order...

SKU: SF-BOB-16842 | Brand: SparkFun

Buttons are an easy and tactile way to interface with your project, but why would you want to deal with debouncing, polling, and wiring up pull-up resistors? The Qwiic Button with built-in green LED simplifies all of ...

SKU: EF-EF04079 | Brand: ElecFreaks

Octopus TMP36 Temperature Sensor Brick is a temperature sensor with low voltage and accurate celsius read. It can provide voltage output,which forms a linear relationship with celsius temperature. TMP36 do not need an...

SKU: EC-MCS01108S | Brand: Elecrow

The ELE Bluetooth Shield V1.2 adds wireless serial communication to your Arduino or Crowduino via Bluetooth V2.0+EDR. Simply stack it onto your board, select two digital pins (D0–D7) for software serial, and start sen...

SKU: EC-CDE20032P | Brand: Elecrow

An Arduino Uno shield that makes it easy to drive a 16×32 RGB LED matrix panel with a HUB75 connector. Instead of wiring up 12 individual jumper wires, this shield provides a matching 2×8 IDC connector for a clean, re...

SKU: SF-PRT-16581 | Brand: SparkFun

A 2×18 pin female header with standard 0.1" (2.54 mm) pitch spacing. Mates perfectly with the Alchitry Br Prototype Element Board and other 0.1"-spaced dual-row male headers. Specifications Configuration – 2×18 (36...

SKU: EC-RA000022RK | Brand: Elecrow

The GPIO extension kit used for extending the GPIO interface on Raspberry Pi B+, it helps you break out all those tasty power, GPIO, I2C and SPI pins from the 40 pin header of Raspberry Pi B+ onto a breadboard.There i...

SKU: EF-EF03091 | Brand: ElecFreaks

The Wireless Charging Module can be applied in electronic equipments in common use for close wireless charging or power supply. Consisted of a transmitter and insolation coil, it could serve as a replacement for th...

SKU: EF-EF03085 | Brand: ElecFreaks

The HC-SR04 is a widely used ultrasonic distance sensor that provides non-contact measurement from 2 cm to 450 cm with up to 3 mm resolution. It uses a 40 kHz ultrasonic transducer pair — one transmitter and one recei...

SKU: SF-COM-16305 | Brand: SparkFun

Amphenol FCI FFC/FPC Flexible Circuit Connectors are a broad range of innovative connector solutions to terminate FFC/FPC. This 24-Pin FPC connector has a 0.5mm pitch and comes with a bottom contact in a right angle o...

SKU: SF-DEV-15837 | Brand: SparkFun

The SparkFun weather:bit is a fully loaded "carrier" board for the micro:bit that, when combined with the micro:bit, provides you with a fully functional weather station. With the weather:bit you will have acces...

SKU: AF-4482 | Brand: Adafruit

These premium male-male jumper wires are handy for making wire harnesses or jumpering between headers on PCBs. They're 200mm (~7.8") long and come loose as a pack of 40 (10 pieces of red, blue, yellow, and Adafruit bl...

SKU: DF-DFR0646-R | Brand: DFRobot

An 8-digit red LED segment display module with Gravity I2C interface. This module can display numbers, basic characters, and supports 16 levels of brightness adjustment — ideal for clocks, counters, dashboards, and da...

SKU: AF-2598 | Brand: Adafruit

The Adafruit Feather M0 WiFi combines an ATSAMD21G18 ARM Cortex M0+ processor with an ATWINC1500 WiFi module for an all-in-one Arduino-compatible development board with built-in USB, battery charging, and 802.11b/g/n ...

SKU: EF-EF09087 | Brand: ElecFreaks

The Geekservo Motor is a compact DC motor designed to be fully compatible with LEGO building systems. Its LEGO-compatible mounting points let you integrate motorised movement directly into brick-based builds, making i...

SKU: EF-EF04017 | Brand: ElecFreaks

Octopus Electronic Bricks, you can use them to build electronics projects just as easy as piling bricks. By using Octopus electronic bricks, you may connect Arduino / Freaduino compatible boards easily with various...

SKU: EF-EF03435 | Brand: ElecFreaks

An accessory pack for the ElecFreaks Ring:bit Car V2, adding obstacle avoidance, line-following, and colourful LED lighting to your micro:bit-powered car. The kit includes three modules that plug directly into the Rin...