New Arrivals

SKU: AF-3647 | Brand: Adafruit

Precision-machined Swiss-pin male plug headers for a tight, reliable fit. Unlike standard stamped square-pin male headers, these use machined round pins that pair exclusively with Swiss-pin female sockets — they are n...

SKU: DF-SEN0230 | Brand: DFRobot

This is an industrial incremental photoelectric rotary encoder with aluminum material, metal shell and stainless steel shaft. It generates AB two-phase orthogonal pulse signal though the rotation of the grating dis...

SKU: DF-DFR0464 | Brand: DFRobot

A 16×2 character LCD module with full RGB backlight, communicating over I2C for minimal wiring. With support for 16 million backlight colours, this display adds a vibrant, customisable readout to your Arduino or compa...

SKU: AF-937 | Brand: Adafruit

This handy USB extension cable will make it easy for you to enclose a device that has a micro-B type port. We think this would be most handy when putting an Arduino Leonardo or Raspberry Pi in a box.The jack half h...

SKU: AF-1070 | Brand: Adafruit

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface.These sensors are easy to use, they are basically resistors that chan...

SKU: AF-1178 | Brand: Adafruit

Rollin' rollin' rollin', you can now roll around smooth as silk with these radial bearings. Often referred to as "skate bearings" They're good for supporting a rotating rod or as a wheel hub. However, these are higher...

SKU: LB-LS1216 | Brand: Little Bird

This sensor is composed of an infrared emitter on one upright and a shielded infrared detector on the other. By emitting a beam of infrared light from one upright to the other, the sensor can detect when an object pas...

SKU: LB-LS0070 | Brand: Little Bird

The knob is designed to set directly on the potentiometer's ridges so it's an easy & secure fit. It has a nice feel, with a solid grip, tweaking it is quite fulfilling This is the red version and it has a nice deep...

SKU: LB-LR0379 | Brand: Little Bird

This crimping tool can be used to crimp both male and female versions of our Tamiya connector crimp pins, mini Tamiya connector crimp pins, JST RCY connector crimp pins, JR crimp pins, Futa...

SKU: AF-1756 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-1755 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-1663 | Brand: Adafruit

A matching pair of 3-pin JST SM connector cables — one plug and one receptacle — for creating quick-connect/disconnect points in 3-wire circuits. The locking latch keeps the connection secure while still allowing easy...

SKU: AF-2195 | Brand: Adafruit

A 10-pack of 10µF 50V electrolytic capacitors with long, flexible leads that make them easy to use on breadboards and perfboard. Each capacitor has clear labelling on the body for quick identification. Electrolytic c...

SKU: AF-2193 | Brand: Adafruit

A 10-pack of 100µF 16V electrolytic capacitors with long, flexible leads that make them easy to use on breadboards and perfboard. Each capacitor has clear labelling on the body for quick identification. Electrolytic ...

SKU: AF-2215 | Brand: Adafruit

A 16.000 MHz quartz crystal in the HC49/US short-style package, supplied with two 20pF load capacitors. The crystal provides higher precision than ceramic resonators, with 30 PPM tolerance and 50 PPM stability — suita...

SKU: AF-2166 | Brand: Adafruit

A low-dropout (LDO) 3.3 V linear voltage regulator based on the ST L4931 in a TO-92 package. With just 0.4 V dropout, it delivers a clean, regulated 3.3 V output from input voltages as low as 3.7 V — well suited for s...

SKU: AF-2442 | Brand: Adafruit

Need to make a tiny robot? This little micro servo rotates 360 degrees fully forward or backwards, instead of moving to a single position. You can use any servo code, hardware or library to control these servos. ...

SKU: DF-FIT0085 | Brand: DFRobot

This custom-designed plastic wheel has a rubber tire measuring 1.65" (42 mm) in diameter and is designed to fit the output shafts on our mini metal gearmotors as well as the Solarbotics metal gear motors. Teeth on...

SKU: DF-SEN0032 | Brand: DFRobot

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos ...

SKU: DF-FIT0521 | Brand: DFRobot

This is a metal geared DC motor w/Encoder. It is a 6V motor with a 34:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 11 counts per revolution of the motor shaft, which corresponds ...