Headers & Connectors

SKU: SF-PRT-10371 | Brand: SparkFun

This is a simple six wire cable. Great for jumping from board to board or just about anything else. There is a 6-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers...

SKU: AF-616 | Brand: Adafruit

Give yourself some more room with an EL wire cable extender. This cable has a 2-pin JST SM plug on one end and receptacle on the other. Use it to extend the reach of EL wire, panel, tape, etc. The cable is a meter ...

SKU: AF-874 | Brand: Adafruit

These are like the fancy electronics equivalent of the wire nuts electricians use to bind wires together. They are a lot easier to use as well! Each block connector has a metal block inside and five levers that sna...

SKU: TB-WV7300 | Brand: Little Bird

 RG- 59U coaxial cable. BNC plug to plug. Specifications  | Audio/Video Signal Type  |  AV | Lead Output Connection  |  Plug | Output Quantity  |  1pc | L...

SKU: DF-FIT0957 | Brand: DFRobot

The IPEX4 to SMA Female Connector Cable is a 200 mm adapter designed for single-board computers equipped with an IPEX4 (MHF4) wireless interface, including the LattePanda 3 Delta, LattePanda 2 Alpha, and LattePanda 2 ...

SKU: AF-6071 | Brand: Adafruit

This panel mount cable is great for making USB Host or (some) client connections with a panel-mount setup. On the small panel-mount side you get a USB C connector, the other end has power, ground and D+ / D- lines. We...

SKU: AF-5993 | Brand: Adafruit

The Adafruit USB Type C Vertical Breakout (Downstream Connection) provides easy access to all the pins on a USB-C connector in a vertical orientation, ideal for breadboard use and enclosure mounting. Two 5.1K resistor...

SKU: AF-5978 | Brand: Adafruit

The Adafruit USB Type C Plug Breakout gives you easy access to the pins on a USB-C plug connector, making it simple to add a USB-C connection to your projects. A 5.1K resistor on the CC1 pin signals the upstream host ...

SKU: AF-5859 | Brand: Adafruit

If you need to add a panel-mount connection for telephone-interfacing projects but don't have the time or ability to cut a custom oval or square hole, this RJ-12 or RJ-11 Telephone Round Panel Mount Plug is the easies...

SKU: SF-CAB-22038 | Brand: SparkFun

This is a basic RP-SMA (Reverse Polarity Sub-Miniature A) male to female connector cable. Each cable is 10M (393.7in.) long with RG58 housing. The RP-SMA connectors at each end are small enough for most consumer GPS, ...

SKU: SF-CAB-22034 | Brand: SparkFun

A 25 cm (9.8″) SMA male-to-female extension cable with RG174 coaxial housing. Ideal for mounting an antenna on the outside of an enclosure while keeping the RF module or GPS receiver safely inside. The threaded SMA co...

SKU: AF-5614 | Brand: Adafruit

Snap action wiring blocks make it easy to connect and split wires without soldering, crimping, or tools. This 3-to-9 block has three colour-coded inputs (green, yellow, red), each fanning out to three matching outputs...

SKU: AF-5468 | Brand: Adafruit

These DIY magnetic connectors let you add MagSafe-style snap-together connections to your own projects. Each set includes two matching halves with seven spring-loaded pogo pins at 2.2 mm pitch and embedded magnets tha...

SKU: AF-5391 | Brand: Adafruit

If you're messing around with floppy drives, or disk drives, or other devices that are usually powered with a PC motherboard you'll often see these big 'Molex' connectors used to provide power. They are used to give 5...

SKU: DF-FIT0773 | Brand: DFRobot

The Gravity 4Pin I2C/UART sensor cable is a standard Gravity series 4-Pin cable with 50cm length. One side is PH2.0-4p connector and the other side is XH2.54 DuPont port, compatible with standard breadboard pin pitch ...

SKU: DF-FIT0756 | Brand: DFRobot

This high-quality 50cm digital sensor cable is equipped with a 3-pin PH2.0 plug connector on one side and a 3-pin DuPont connector on the other side. They are specially designed for our popular IO Expansion shield and...

SKU: DF-FIT0856 | Brand: DFRobot

This DB9 Male to RJ45 Female Adapter can be used to handle serial data communication between RS232 devices with one RJ45 network cable, or as an extender to extend RS232 serial signal to about 20m.Two modules are requ...

SKU: DF-FIT0859 | Brand: DFRobot

This DB15 Female to RJ45 Female Adapter can be used to handle data communication between VGA interface devices with one RJ45 network cable, or as an extender to extend VGA signal to about 20m.Two modules are required ...

SKU: DF-FIT0865 | Brand: DFRobot

A set of five solderless LED strip pigtail cables, each with a snap-down connector on one end for 10 mm wide 3-wire LED strips and a DuPont-style female connector on the other. The 20 cm colour-labelled wires with mar...

SKU: DF-FIT0863 | Brand: DFRobot

A set of five solderless snap-down connector cables for joining 10 mm wide, 3-wire LED strips with a wire bridge between them. Each cable has snap-down connectors on both ends — simply align the strip's copper pads an...