Environmental (temperature, humidity, air quality)

SKU: LB-LR0214-16 | Brand: Little Bird

This compact 12V temperature controller features a 3-digit LED display for setting and monitoring temperature, along with a built-in 10A relay for switching heating or cooling loads. It uses an NTC thermistor probe (i...

SKU: LB-LR0102 | Brand: Little Bird

The DHT22 (also known in Australia by RHT03) is a low cost humidity and temperature sensor with a single wire digital interface. The sensor comes pre-calibrated and in a breadboard compatible module form so you don...

SKU: LB-LS2696 | Brand: Little Bird

A waterproof NTC thermistor temperature sensor with a 100cm (1 metre) cable and stainless steel probe. The 10KΩ resistance at 25°C and standard B-constant make it easy to read with an Arduino or other microcontroller ...

SKU: LB-LR0298 | Brand: Little Bird

This stand alone DHT11 can read the temperature and humidity and send the information over a one wire, simplex serial bus. Arduino.cc provides a DHT11 library to aid in communicating with this module.**DHT11 Temper...

SKU: LB-LR0285 | Brand: Little Bird

Feature: 0.5°C Ensured Accuracy (+25°C) Suitable for Remote Applications Low Cost Due to Wafer-Level Trimming Operates from 4 to 30 V Less than 60-μA Current Drain Low Self-Heating, 0.08°C in Still Air Low Impedance O...

SKU: AF-3984 | Brand: Adafruit

For precision temperature sensing, nothing beats a Platinum RTD. Resistance temperature detectors (RTDs) are temperature sensors that contain a resistor that changes resistance value as its temperature changes, bas...

SKU: AF-372 | Brand: Adafruit

An epoxy-coated precision NTC thermistor with a 10kΩ resistance at 25°C and ±1% accuracy. The resistance decreases as temperature rises and increases as it cools, making it straightforward to measure temperature with ...

SKU: AF-3290 | Brand: Adafruit

A platinum resistance temperature detector (RTD) with a 100 Ω resistance at 0°C, offering superior accuracy and long-term stability compared to thermocouples and thermistors. PT100 sensors are widely used in laborator...

SKU: TB-RN3444 | Brand: Little Bird

A 100 kΩ NTC (Negative Temperature Coefficient) thermistor in a radial dipped-epoxy package. These ceramic sensors change resistance rapidly with temperature, making them ideal for temperature measurement, compensatio...

SKU: DF-SEN0139 | Brand: DFRobot

This is a K type Thermocouple (Temperature sensor) which is very popular for 3D printers such as Ultimaker and Makerbot. You can hardly damage them or mishandle them. You just need an additional IC (Like an AD595) ...

SKU: AF-576 | Brand: Adafruit

Put a temperature meter anywhere with this very handy display. This panel meter displays the temperature of the attached waterproof 1% thermistor in °C. It does require a DC voltage to run, at 4.5-30VDC. It has revers...

SKU: SF-SEN-17052 | Brand: SparkFun

The MQ-136 is a Hydrogen Sulfide detection sensor with a sensing range of 1 - 200ppm. The sensing element is SnO2, which has lower conductivity in clean air. When H₂S gas exists, the sensor’s conductivity gets higher ...

SKU: TB-RN3442 | Brand: Little Bird

A 47 kΩ NTC (Negative Temperature Coefficient) thermistor in a compact 5 mm radial package. NTC thermistors decrease in resistance as temperature rises, making them ideal for temperature sensing, thermal protection, a...

SKU: TB-RN3436 | Brand: Little Bird

A 1 kΩ NTC (negative temperature coefficient) thermistor in a 5 mm radial dipped-epoxy package. The resistance decreases as temperature increases, making it suitable for temperature sensing, thermal compensation, and ...

SKU: DF-DFR0280 | Brand: DFRobot

Sharp GP2Y1010AU Dust Sensor requires some wiring on the breadboard and a list of components to make it Arduino compatible. This has turned down several people due to the thin wires of the sharp sensor making it ...

SKU: AF-249 | Brand: Adafruit

This pack includes everything you need to build a light and temperature data logger with an Arduino. The Adafruit data logger shield records sensor readings to an SD card with real-time timestamps, while the included ...

SKU: SF-SEN-28868 | Brand: SparkFun

This wind vane is used to indicate the direction from which the wind is blowing. Inside the vane are eight switches, each paired with a unique resistor, allowing a microcontroller to read direction based on the vane’s...

SKU: DF-SEN0475 | Brand: DFRobot

Measure hydrogen fluoride concentration with a factory-calibrated electrochemical probe that supports analogue, I2C and UART output modes. It is designed for quickly building an HF concentration detector for industria...

SKU: DF-SEN0469 | Brand: DFRobot

This calibrated gas sensor measures ammonia concentration in the environment using an electrochemical probe. It supports three output modes — analogue, I2C and UART — so it can slot into a wide range of microcontrolle...

SKU: LB-DHT11-SENSOR | Brand: Little Bird

The Little Bird DHT11 Temperature and Humidity Sensor Module provides calibrated digital temperature and humidity readings from a single sensor. Designed and made in Sydney, Australia, it requires no extra components ...