Enclosures & Hardware

SKU: AF-550 | Brand: Adafruit

Small self-adhesive rubber bumper feet for electronics boards and devices. Stick them to the bottom of any PCB to protect your desk, prevent sliding, and provide clearance for through-hole solder joints underneath. T...

SKU: DF-FIT0604 | Brand: DFRobot

A transparent ABS case designed for the Raspberry Pi Zero and Zero W. The case features large cutouts for the GPIO header and camera port, keeping all connections accessible while protecting the board. The GPIO 40-pin...

SKU: LB-LS2209 | Brand: Little Bird

A mounting bracket designed to attach an HC-SR04 ultrasonic ranging module and an analogue servo to a smart car chassis. Enables pan-and-scan obstacle detection for robotics projects. Key Features HC-SR04 Compatibl...

SKU: AF-2337 | Brand: Adafruit

Finally we get our very own super sweet sixteen... 16 millimeters that is! Our Black Plated M/F Brass 16mm Standoffs are engineered specifically to keep your PiTFT or other Pi accessories w...

SKU: SF-PRT-08432 | Brand: SparkFun

Screw Terminals with 5mm pitch pins. Comes in 2 or 3 positions and have the really cool feature of slide-locking together to form any size you need (4, 5, up to 20 without problems). Rated up to 300V @ 8A. Terminal...

SKU: SF-PRT-11476 | Brand: SparkFun

This barrel jack plug is great for adding a common connector to the end of our wires. This jack is compatible with 5.5mm barrel jacks that have a 2.1mm center pole diameter. The outer shell unscrews to reveal solder t...

SKU: AF-5774 | Brand: Adafruit

The Adafruit Swirly Aluminum Mounting Grid provides a mechanical substrate for mounting small microcontroller boards, sensors, and Feathers that use STEMMA QT plug-and-play connections. When you're snapping boards tog...

SKU: AF-3949 | Brand: Adafruit

A compact steel ball caster that provides smooth, omnidirectional movement for small robots and wheeled projects. With a 16mm overall height, it's well-suited as a third support point for two-wheeled robot chassis. E...

SKU: AF-3700 | Brand: Adafruit

A candy-coloured zipper case that's the perfect size for makers on the go. Instead of tossing your Raspberry Pi or Metro M0 Express into the abyss of your backpack, keep it safe and organised in this compact pouch. S...

SKU: AF-1493 | Brand: Adafruit

A compact aluminium heat sink designed for surface-mount components such as SoCs, motor drivers, linear regulators, FETs, and other SMT packages. Its small footprint and tall fin design provide effective thermal dissi...

SKU: AF-2174 | Brand: Adafruit

Keep your 5 mm LEDs securely mounted with these lightweight plastic LED holders featuring a bevelled finish. Simply slot the LED through the opening and it snaps into place — no tools or hardware needed. The bevelled ...

SKU: SF-COM-09278 | Brand: SparkFun

It’s not what project you have in mind that may use a rocket launch switch… The question is what project will you come up with once you have one in hand? Everyone has a proverbial missile to launch.The hot red safety ...

SKU: DF-FIT0191 | Brand: DFRobot

A compact aluminium heat sink with pre-applied 3M 8810 thermal adhesive tape on the back. Simply peel off the blue protective film and stick it directly onto your IC or chip — no thermal paste or glue required. The ad...

SKU: SF-PRT-08433 | Brand: SparkFun

Screw Terminals with 5mm pitch pins. Comes in 2 or 3 positions and have the really cool feature of slide-locking together to form any size you need (4, 5, up to 20 without problems). Rated up to 300V @ 8A. Terminal ca...

SKU: SF-COM-11841 | Brand: SparkFun

A snap-in plastic LED holder designed for 10 mm LEDs. Simply press the LED into the holder and snap the assembly into a 35/64″ (approximately 14 mm) panel hole — no screws or tools required. Key Features Snap-In De...

SKU: DF-FIT0991 | Brand: DFRobot

The Argon NEO 5 BRED is a polished aluminium case for the Raspberry Pi 5, combining passive heatsink cooling with an integrated active cooling fan. Cold air enters through intake vents and the fan circulates airflow t...

SKU: AF-5019 | Brand: Adafruit

These 1mm thick double-sided foam tapes are perfect for a variety of small projects. These adhesive rectangles provide a strong bond to most surfaces and are cleaner and easier to remove witho...

SKU: AF-1434 | Brand: Adafruit

A two-piece adjustable mount from Pimoroni for the Raspberry Pi Camera Module. The design allows multiple angle positions and includes a 1/4"-20 threaded hole for attaching to a standard camera tripod. Compatible wit...

SKU: AF-1467 | Brand: Adafruit

Get that heat sink stuck on good and strong with 3M's thermal tape. Specifically designed for attaching heat sinks to ICs. Works better and is less messy than thermal glues or pastes because the thickness is even acro...

SKU: AF-1515 | Brand: Adafruit

A 10-pack of ultra-low-profile aluminium heat sinks designed for surface-mount components such as SoCs, motor drivers, linear regulators, FETs, and other SMT packages. Their tiny footprint and minimal height make them...