Components

SKU: AF-4783 | Brand: Adafruit

Here's a handy 3-pack of 2cm x 8cm Proto-board PCBs in Adafruit Black. Both sides have a black silkscreen with some row/column markings. Note that these don't have any traces between the PCB holes, you would normally ...

SKU: DF-FIT0727 | Brand: DFRobot

Waterproof is always a critical point for outdoor projects, and when you need to drill holes on a project enclosure to lead out the wires, it will be very likely to cause the waterproof problem. Now no more worries, w...

SKU: AF-4613 | Brand: Adafruit

This ultra-flexible warm white LED strip uses chip-on-board (COB) technology with 320 SMT LEDs per metre, producing a continuous, even glow without visible LED dots. Covered in a translucent silicone diffuser and seal...

SKU: AF-4612 | Brand: Adafruit

Here at Adafruit we love discovering new and exotic glowing things. Like moths to the flame, we were intrigued by these 'chip on board' ultra-flexible white LED Strips with 320 SMT LEDs per meter, soldered side-by-sid...

SKU: LB-LR0301 | Brand: Little Bird

Mini 5V DC Power Relay SRD-5VDC-SL-C 5 Pin PCB TypeFeature:Selection of plastic material for high temperature and better chemical solution performanceSpecification:Coil voltage: DC 5VCoil resistance: 70Ω ~ 80ΩContact ...

SKU: AF-4767 | Brand: Adafruit

Here's a handy power cable for the RGB LED Matrix Panels we carry.Easily plug into the back of your RGB matrix and insert or screw the power and ground cables onto either the Matrix Portal or the Matrix Bonnet, or whi...

SKU: AF-4764 | Brand: Adafruit

These 2-prong barbed fitting connectors are designed for use with silicone tubing in air pump and valve setups. Each port has an outer diameter of approximately 4mm, creating a secure seal with 2–3mm ID silicone tubin...

SKU: SF-COM-17263 | Brand: SparkFun

This is a "deluxe" joystick knob very similar to the thumb pads on PlayStation controllers. We specifically carry this knob to pair with our 16mm Deluxe Thumb Joystick.

SKU: SF-COM-16273 | Brand: SparkFun

A 16 mm deluxe thumb joystick similar to the analogue sticks found in PlayStation controllers. Two 10K potentiometers provide analogue position data for the full range of motion on both axes, and a built-in select but...

SKU: DF-FIT0676 | Brand: DFRobot

A WS2812B addressable RGB LED ring lamp composed of 93 LEDs arranged in 6 concentric rings. Each ring can be controlled independently or cascaded together, and individual rings can be cut apart and recombined into cus...

SKU: AF-4763 | Brand: Adafruit

These little chips are like miniature SSD drives for your electronics. When you don't need something with as much storage as a micro SD card, but an EEPROM is too small, SPI (or QSPI) Flash chips give you on-the-order...

SKU: AF-4749 | Brand: Adafruit

A nice whoppin' rectangular slab of some lovely black acrylic to add some extra diffusion to your LED Matrix project. This material is 2.6mm (0.1") thick and is made of special cast acrylic that makes it perfect for g...

SKU: AF-4726 | Brand: Adafruit

A ZIF (zero insertion force) socket for wide-body SOIC-8 (200mil) chips. Flip open the latch, insert your chip, and close it to secure the IC against gold contact fingers. The bottom footprint matches the standard SOI...

SKU: AF-4662 | Brand: Adafruit

These T-shaped barbed connectors allow you to split or combine silicone tubing runs into three-way junctions. Each port has an outer diameter of approximately 4 mm, designed to fit snugly with 3 mm ID silicone tubing ...

SKU: AF-4689 | Brand: Adafruit

Peep this NeoPixel RGBW Neon-like LED Flex Strip with Silicone Tubing! OK its a bit of a mouthful but check out the beautiful pics! It has a diffused look like neon, but without the need for expensive transformers, gl...

SKU: SF-BOB-16842 | Brand: SparkFun

Buttons are an easy and tactile way to interface with your project, but why would you want to deal with debouncing, polling, and wiring up pull-up resistors? The Qwiic Button with built-in green LED simplifies all of ...

SKU: EC-CDE20032P | Brand: Elecrow

An Arduino Uno shield that makes it easy to drive a 16×32 RGB LED matrix panel with a HUB75 connector. Instead of wiring up 12 individual jumper wires, this shield provides a matching 2×8 IDC connector for a clean, re...

SKU: EC-CCC12311K | Brand: Elecrow

A set of stackable female headers for Arduino UNO and compatible boards. The extended contact length clears the USB-B connector, making them ideal for stacking multiple shields. Details Compatibility – Arduino UNO,...

SKU: AF-4512 | Brand: Adafruit

Make your own custom DE-9 cable or DE-9 interface with ease, using this DE-9 Plug to Terminal Spring Block Adapter. You get a nice solid PCB with a DE-9 plug and one line of push-spring terminal blocks that you can us...

SKU: AF-4594 | Brand: Adafruit

A sheet of black LED diffusion acrylic designed to enhance the look of LED matrix and NeoPixel projects. This specially cast acrylic sharpens individual pixels and reduces glare, delivering vivid, readable colours bot...