Circuitry & IOT

SKU: DF-DFR0359 | Brand: DFRobot

INTRODUCTION eClip is an innovative programming/testing tool specially designed for Makers. It solves the problem of prototyping wearable projects with ICSP and FTDI interfaces in limited spa...

SKU: AF-3286 | Brand: Adafruit

A slim 3×AAA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making i...

SKU: AF-3287 | Brand: Adafruit

A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making...

SKU: SF-PRT-10592 | Brand: SparkFun

This is the SMD version of PRT-07948, which is the unit we like to use as RTC backup and SRAM backup for GPS units. Holds battery in place with friction. The metal housing connects to the positive side of the batte...

SKU: PL-1919 | Brand: Pololu

These 1×12-pin crimp connector housings let you quickly build custom cables that mate with standard 0.1" (2.54mm) spaced connectors. Pair them with pre-crimped terminal wires to create reliable, removable multi-wire c...

SKU: PL-1918 | Brand: Pololu

These 2×16-pin crimp connector housings let you quickly build custom cables that mate with standard 0.1" (2.54mm) spaced connectors. Pair them with pre-crimped terminal wires to create reliable, removable 32-wire conn...

SKU: SF-PRT-10512 | Brand: SparkFun

A snap-in 9V battery holder with a 5.5mm/2.1mm centre-positive barrel jack connector. The battery clicks securely into place, and three mounting holes allow you to attach the holder to an enclosure or chassis. Key Fe...

SKU: PL-1909 | Brand: Pololu

These ten-pin crimp connector housings let you quickly build custom cables that mate with standard 0.1" (2.54mm) spaced connectors. Pair them with pre-crimped terminal wires to create reliable, removable multi-wire co...

SKU: DF-KIT0098 | Brand: DFRobot

INTRODUCTION Breadboard-Plugin Components Pack is a new kit designed for breadboard experiment. It provides many kinds of components, such as resistors, capacitors, diodes, transistor .et...

SKU: SF-PRT-12699 | Brand: SparkFun

This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prot...

SKU: DF-FIT0425 | Brand: DFRobot

The ECell Breadboard-Plugin LED pack contains 8 colour-coded LEDs mounted on gold-plated breadboard-compatible modules. Each module has clearly marked polarity and circuit symbols, making it easy to identify component...

SKU: DF-FIT0423 | Brand: DFRobot

INTRODUCTION Introducing "The Breadboard-Plugin Kit" - the first kit in the ECell series. The Breadboard-Plugin Kit provides a range of common components such as resistors, capacitors,...

SKU: DF-KIT0111 | Brand: DFRobot

The Gravity Starter Kit for Arduino is a plug-and-play electronics toolkit designed for beginners and makers getting started with the Arduino platform. It includes a DFRduino UNO R3 microcontroller (fully compatible w...

SKU: AF-1898 | Brand: Adafruit

Listen up! This 1.1" (~30mm) diameter speaker is the perfect addition to any breadboard-based audio project where you need 8 Ohm impedance, and have 0.2W or less of power. The two pins are 15mm / 0.6" apart and ...

SKU: AF-3391 | Brand: Adafruit

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a log taper 10K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will shift on its own...

SKU: AF-770 | Brand: Adafruit

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the ca...

SKU: SF-PRT-09390 | Brand: SparkFun

This is a SparkFun exclusive! These are 12" long jumper wires terminated as female to female. Use these to jumper from any male header on any board. Multiple jumpers can be connected next to one another on a 0.1" h...

SKU: SS-114991884 | Brand: Seeed Studio

The BitCar is a micro:bit-powered robot car kit featuring autonomous line following, ultrasonic obstacle avoidance, and remote control capabilities. Built around a sturdy chassis with two metal gear motors, the car in...

SKU: PL-1013 | Brand: Pololu

This connector is a single-row, 3-pin, straight female header strip designed to match 0.1" male headers. The order quantity must be a multiple of five.

SKU: AF-3366 | Brand: Adafruit

Stacking headers combine a female socket on top with extended male pins on the bottom, allowing you to stack multiple PCBs on top of each other. Solder the long pins through a board, then plug another board's female h...