Circuitry Accessories

SKU: SF-PRT-11710 | Brand: SparkFun

Jumper wires are awesome. Just a little bit of stranded core wire with a nice solid female connector on either end. They have the flexibility of stranded wire but will fit directly onto male pin headers. The only down...

SKU: SF-PRT-11709 | Brand: SparkFun

Jumper wires are awesome. Just a little bit of stranded core wire with a nice solid pin connector on either end. They have the flexibility of stranded wire but will fit directly into breadboards and female pin head...

SKU: SF-PRT-00111 | Brand: SparkFun

A standard alligator clip — an essential tool for any electronics workbench. Use it for making quick temporary connections when prototyping circuits, testing components, or extending test leads. Ideal For Prototypin...

SKU: AF-65 | Brand: Adafruit

A tiny solderless breadboard that's half the size of a half-size breadboard — perfect for compact prototypes, small circuits, and sticking onto the top of Arduino protoshields. Specifications Dimensions – 46 × 36 m...

SKU: AF-248 | Brand: Adafruit

A 6×AA battery holder with a 5.5mm/2.1mm DC barrel plug, ready to power Arduino boards and other electronics with a standard DC jack. Use alkaline AAs for approximately 9V at 3000–4000mAh, or rechargeable NiMH cells f...

SKU: AF-275 | Brand: Adafruit

By popular demand! We now have the plates from the ARDX available separately. Acrylic plate is engraved and cut here at the Adafruit factory. There are mounting holes for your Arduino and a space that fits a half s...

SKU: AF-3286 | Brand: Adafruit

A slim 3×AAA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making i...

SKU: AF-3287 | Brand: Adafruit

A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making...

SKU: SF-PRT-10512 | Brand: SparkFun

A snap-in 9V battery holder with a 5.5mm/2.1mm centre-positive barrel jack connector. The battery clicks securely into place, and three mounting holes allow you to attach the holder to an enclosure or chassis. Key Fe...

SKU: DF-KIT0098 | Brand: DFRobot

INTRODUCTION Breadboard-Plugin Components Pack is a new kit designed for breadboard experiment. It provides many kinds of components, such as resistors, capacitors, diodes, transistor .et...

SKU: SF-PRT-12699 | Brand: SparkFun

This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prot...

SKU: DF-FIT0425 | Brand: DFRobot

The ECell Breadboard-Plugin LED pack contains 8 colour-coded LEDs mounted on gold-plated breadboard-compatible modules. Each module has clearly marked polarity and circuit symbols, making it easy to identify component...

SKU: DF-FIT0423 | Brand: DFRobot

INTRODUCTION Introducing "The Breadboard-Plugin Kit" - the first kit in the ECell series. The Breadboard-Plugin Kit provides a range of common components such as resistors, capacitors,...

SKU: AF-1898 | Brand: Adafruit

Listen up! This 1.1" (~30mm) diameter speaker is the perfect addition to any breadboard-based audio project where you need 8 Ohm impedance, and have 0.2W or less of power. The two pins are 15mm / 0.6" apart and ...

SKU: AF-3391 | Brand: Adafruit

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a log taper 10K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will shift on its own...

SKU: AF-770 | Brand: Adafruit

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the ca...

SKU: SF-PRT-09390 | Brand: SparkFun

This is a SparkFun exclusive! These are 12" long jumper wires terminated as female to female. Use these to jumper from any male header on any board. Multiple jumpers can be connected next to one another on a 0.1" h...

SKU: AF-3366 | Brand: Adafruit

Stacking headers combine a female socket on top with extended male pins on the bottom, allowing you to stack multiple PCBs on top of each other. Solder the long pins through a board, then plug another board's female h...

SKU: DF-FIT0908 | Brand: DFRobot

This kit includes two kinds of mini multi-color block building breadboards and 2 base plates of different sizes. Users can freely assemble these breadboards to make various projects combining with other microcontrolle...

SKU: AF-5515 | Brand: Adafruit

Stretch out your servo connections with this flexible servo to premium male header jumper cable. It has a 3-pin shrouded "male" connector to plug the servo into and then, 17cm later, three separated jumper wire e...