Circuitry Accessories

SKU: LB-LS7240-H | Brand: Little Bird

Introducing the perfect solution for prototyping - our Half-size Permanent Solder Breadboard PCB! With this board, you can easily transfer your circuit from a solderless breadboard to a more permanent solution wi...

SKU: EF-EF10095 | Brand: ElecFreaks

A 2×AA battery holder designed specifically for the BBC micro:bit. The built-in JST PH connector plugs directly into the micro:bit's battery socket, and the integrated on/off switch with a secure cover provides safe, ...

SKU: AF-1699 | Brand: Adafruit

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm...

SKU: SF-PRT-12083 | Brand: SparkFun

This 4xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF swi...

SKU: AF-239 | Brand: Adafruit

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the powe...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: LB-LR0178-350 | Brand: Little Bird

SKU: DF-FIT0610 | Brand: DFRobot

This enclosed battery holder takes 3× AA batteries in series, providing approximately 4.5V from alkaline cells or 3.6V from NiMH/NiCd rechargeables. It features a built-in on/off switch and a sliding, removable cover ...

SKU: AF-4193 | Brand: Adafruit

A slim 2×AA battery holder with a built-in on/off switch and genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and p...

SKU: AF-4031 | Brand: Adafruit

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack so you get left and right channels as well as a ground pin. You can use any 3.5mm stereo cable with this jac...

SKU: DF-FIT0121 | Brand: DFRobot

Jumper wires are one of the most important gear component for the tinkerer. Often underestimated, but one of the first things to miss. If you are starting to assemble your tinker gear and wondering if this is really n...

SKU: AF-1951 | Brand: Adafruit

These premium female-to-female jumper wires are ideal for making wire harnesses or connecting between headers on PCBs. Each pack contains 20 wires in a ribbon cable format — two of each of ten rainbow colours — that c...

SKU: AF-1953 | Brand: Adafruit

These Female/Male 'extension' jumper wires for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 3" (75mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbow...

SKU: SF-ROB-19223 | Brand: SparkFun

This is a servo adapter cable that allows you to hookup your servo directly to alligator clip connections. On one end you have a shrouded male servo connector, and on the other end three 30mm shrouded alligator clips....

SKU: DF-FIT0079 | Brand: DFRobot

A simple 4-cell AA battery holder in a square (2×2) configuration. Features 5-inch tinned leads for easy soldering into your project. Provides 6V nominal output with four AA alkaline batteries, or 4.8V with rechargeab...

SKU: AF-1608 | Brand: Adafruit

The Adafruit Perma-Proto Quarter-Sized Breadboard PCB mirrors the layout of a tiny solderless breadboard with power rails, making it simple to transfer small prototyped circuits to a permanent soldered board. The comp...

SKU: AF-1789 | Brand: Adafruit

This 1K potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 1K ohm potentiometer, with a grippy shaft. Its smooth and easy to turn, but not so loose that it will ...

SKU: AF-184 | Brand: Adafruit

Build your own breadboard-friendly adjustable power supply with this soldering kit. Based on the MIC2941 low-dropout regulator, it provides a guaranteed 1.25A output with only 40–400 mV dropout — far better than the L...

SKU: SF-PRT-10891 | Brand: SparkFun

This 3xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF swi...

SKU: AF-1831 | Brand: Adafruit

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 100K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will...