Breakouts

SKU: DF-FIT0099 | Brand: DFRobot

A prototyping board is one of the main steps in hardware development, also called a perf board. Breadboard, wiring and punching in chips, resistors and leds is probably the first step. While this is good to confirm a...

SKU: SF-SEN-14348 | Brand: SparkFun

The SparkFun CCS811/BME280 Environmental Combo Breakout takes care of all your atmospheric-quality sensing needs with the popular CCS811 and BME280 ICs. This unique breakout provides a variety of environmental data, i...

SKU: DF-SEN0097 | Brand: DFRobot

This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more acurate and easier ...

SKU: SF-PRT-14322 | Brand: SparkFun

These stackable headers are made to work with the Particle Photon and Photon ProtoShield boards. Each header adds a great deal of connectivity to your next Photon project. Each order includes one 1x12 stackable header...

SKU: DF-DFR0164 | Brand: DFRobot

This is a new version of the FTDI breakout board features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The 8U2 firmware uses the standard USB COM drivers, and no ...

SKU: DF-DFR0175 | Brand: DFRobot

This is a new IIC LCD backpack which supports Gadgeteer interface (IDC10). It allows gadgeteer user to play with LCD160X. The IIC LCD Backpack is a small PCB that can be soldered to the back of an LCD so tha...

SKU: AF-2711 | Brand: Adafruit

With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi  with no soldering or breadboarding! This HAT has screw-terminals for each pin on the Pi Header Key features: Solderl...

SKU: AF-2743 | Brand: Adafruit

This compact adapter board makes it easier to work with ARM development boards that use the slimmer 2x5 SWD programming connector. It is designed for 0.05 inch / 1.27mm pitch SWD cables, commonly found on small Cortex...

SKU: DF-FIT0203 | Brand: DFRobot

This is a very basic double sided prototyping board with standard 0.1" spacing through holes and four 3mm diameter mounting holes. There are 22x26 holes in total. Great for quickly prototyping stackable circuit...

SKU: SF-BOB-09110 | Brand: SparkFun

This is the breakout board for the thumb joystick. Pins are broken out to a 0.1" header and includes 4 mounting holes in the corners.

SKU: AF-2719 | Brand: Adafruit

If you've been diggin' our monochrome OLEDs but need something bigger, this display will delight you! These displays are 2.42" diagonal, and very readable due to the high contrast of an OLED display. This display i...

SKU: SF-BOB-08891 | Brand: SparkFun

This breakout board provides a convenient PCB adapter for MQ-series gas sensors (MQ-3, MQ-4, MQ-6, MQ-7, and MQ-8). It converts the sensor's oversized, oddly-spaced pins into a standard breakout format that's easy to ...

SKU: SF-PRT-08808 | Brand: SparkFun

This is a very simple but extremely handy, 1" square, single sided perf board. Standard 0.1" spacing with a 4-40 (3mm) hole for mounting. Every three holes are connected with a 20mil trace.  Package of 2

SKU: DF-FIT0290 | Brand: DFRobot

This is a SOP8 to DIP8 Adapter Board. You can change the SOP8 to DIP8 packaging.So that You needn't to buy the DIP chips for prototyping specially.Just solder the SMD chips on the board and plug it into the bread b...

SKU: AF-2913 | Brand: Adafruit

If you need to connect an RJ45 cable (a.k.a Ethernet) to a board that with an Ethernet Jack - this adapter will come in very handy! No soldering required. Just use a slim screwdriver to open up the terminal blocks,...

SKU: DF-DFR0250 | Brand: DFRobot

A boost converter module that takes two AA batteries and outputs a stable 5 V supply for your circuits. Built around the TI TPS61032 boost chip, it accepts input voltages from 1.8–4.5 V and delivers up to 5 V @ 1 A — ...

SKU: SF-SEN-11828 | Brand: SparkFun

RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the ID-20LA, a very simpl...

SKU: SF-SEN-11827 | Brand: SparkFun

RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the ID-12LA, a very simpl...

SKU: SF-BOB-11771 | Brand: SparkFun

This is a breakout board for the Texas Instruments TXB0104 module. The TXB0104 is a 4-bit bidirectional voltage-level translator with automatic direction sensing. This 4-bit noninverting translator uses two separate...

SKU: SF-SEN-00242 | Brand: SparkFun

The Sharp GP2Y0A21YK is an infrared proximity sensor with an analogue voltage output that varies with distance — from 3.1 V at 10 cm to 0.4 V at 80 cm. It uses an IR emitter and position-sensitive detector to measure ...