Breakouts

SKU: AF-5907 | Brand: Adafruit

The Adafruit Terminal PiCowbell with Pre-Soldered Sockets gives your Raspberry Pi Pico or Pico W instant plug-and-play access to every GPIO pin via screw terminal blocks. Simply plug in your Pico and connect 18–26 AWG...

SKU: SF-KIT-23451 | Brand: SparkFun

Pogo pins make life so much easier when you are trying to program without having to solder a single thing, and when you attach them to an In-system programming (ISP) adapter, they become instantly better. This simple ...

SKU: SF-SEN-22956 | Brand: SparkFun

The SparkFun Photoacoustic Spectroscopy CO2 Sensor features the Infineon XENSIV PAS CO2 (PASCO2V01) sensor, which delivers highly accurate CO2 measurements in direct parts-per-million (ppm) format. The photoacoustic s...

SKU: DF-SEN0570 | Brand: DFRobot

Fermion: MEMS Smoke Gas Detection Sensor employs state-of-the-art microelectromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat...

SKU: DF-SEN0571 | Brand: DFRobot

Fermion: MEMS Odor Smell Gas Detection Sensor employs state-of-the-art microelectromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal...

SKU: DF-SEN0567 | Brand: DFRobot

Fermion: MEMS Ammonia NH3 Gas Detection Sensor employs state-of-the-art micro-electromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minim...

SKU: LB-COCKATOO | Brand: Little Bird

The Cockatoo is a simple screw-terminal breakout board for the BBC micro:bit. Slide your micro:bit into the edge connector and you get secure screw terminal access to pins 0, 1, 2, 3.3V, and GND — no soldering or croc...

SKU: AF-5709 | Brand: Adafruit

The Adafruit CAN Bus FeatherWing adds CAN bus networking to any Feather board. It uses the MCP2515 CAN controller and TJA1051/3 transceiver to send and receive messages in standard or extended format at up to 1 Mbps o...

SKU: SF-DEV-21247 | Brand: SparkFun

The SparkFun USB-C Host Shield provides all the digital logic and analogue circuitry needed to add USB peripheral/host control to your Arduino. Interface with and control any USB 2.0 compatible device — thumb drives, ...

SKU: DF-DFR0979 | Brand: DFRobot

The Gravity CH423 I2C 24 Digital IO Expansion Module extends your microcontroller with 24 additional digital output/input pins over a standard I2C connection. Based on the CH423 chip, it provides 8 GPIOs with interrup...

SKU: AF-5663 | Brand: Adafruit

Need to use multiple I2C devices that share the same address? The PCA9546 4-Channel I2C Multiplexer lets you connect up to four same-address I2C devices to a single microcontroller by acting as a gatekeeper — write a ...

SKU: AF-5611 | Brand: Adafruit

The Adafruit PCF8575 GPIO Expander Breakout is an affordable 16-channel I2C GPIO expander that doubles your available digital I/O over a simple two-wire connection. Add extra buttons, LEDs, relays, or other digital pe...

SKU: AF-5610 | Brand: Adafruit

The Adafruit LTR-303 is a low-cost I2C digital light sensor that provides 16-bit measurements for both infrared and visible+IR spectrums. Subtract one from the other to get human-visible light readings. With configura...

SKU: SF-SEN-19096 | Brand: SparkFun

The SparkFun BME688 Environmental Sensor is a breakout that combines a gas scanning sensor with temperature, humidity, and barometric pressure sensing for a complete environmental sensor in a single package. The ga...

SKU: SF-SEN-13905 | Brand: SparkFun

The SparkFun BME280 Atmospheric Sensor Breakout measures barometric pressure, relative humidity, and temperature in a compact package. This version comes with headers pre-soldered for easy breadboard use or direct wir...

SKU: DF-SEN0501 | Brand: DFRobot

This multifunctional environmental sensor comprises SHTC3 temperature & humidity sensor, BMP280 barometric pressure sensor, VEML7700 ambient light sensor, and ML8511 UV sensor into one and offers 5 kinds of environmen...

SKU: AF-5315 | Brand: Adafruit

An 8-pin SOIC test clip with a DIP breadboard adapter, designed for in-circuit probing and programming of flash memory, EEPROMs, and other 8-SOIC ICs — no soldering or desoldering required. Simply clip onto the chip t...

SKU: DF-SEN0330 | Brand: DFRobot

This Digital Temperature & Humidity Sensor Breakout Board is based upon the Sensirion SHT30 sensor IC. Thanks to Sensirion’s CMOSens® technology, highly integrated capacitive humidity sensing components and band-gap t...

SKU: DF-SEN0333 | Brand: DFRobot

A high-accuracy digital temperature and humidity sensor breakout board based on the Sensirion SHT35 sensor IC. Using Sensirion's CMOSens technology, the SHT35 delivers excellent long-term stability, low power consumpt...

SKU: DF-DFR0914 | Brand: DFRobot

This DFRobot 4-channel optocoupler-isolated level converter translates 12V signals down to 5V, making it easy to interface industrial sensors and PLC outputs with Arduino and other 5V microcontrollers. Each channel fe...