Breakouts

SKU: SF-TOL-09419 | Brand: SparkFun

The SparkFun microSD Sniffer lets you tap into the SPI traffic between a microSD card and its host device for debugging or reverse engineering. Insert one end into a standard microSD socket and plug a microSD card int...

SKU: SF-PRT-10588 | Brand: SparkFun

Simple breakout board for the 3.5mm audio jack. Use this breakout (shipped bare) to allow breadboard or SIP access to the super-common 3.5mm audio jack. All five pins are broken out.

SKU: DF-SEN0636 | Brand: DFRobot

The Gravity UV Index Sensor measures ultraviolet radiation across the 240–370 nm wavelength range, covering UVA, UVB, and UVC bands. It directly outputs a UV index (0–11) and a harm risk level (1–5), eliminating the n...

SKU: AF-6109 | Brand: Adafruit

The Adafruit A4988 Stepper Motor Driver Breakout simplifies stepper motor control down to just two pins — a direction pin and a step pin. Each pulse on the step pin advances the motor by one step or microstep, making ...

SKU: SF-SEN-24904 | Brand: SparkFun

The SparkFun Qwiic Optical Tracking Odometry Sensor empowers you to elevate your robot's navigation capabilities with exceptional precision and streamlined integration. This compact, all-in-one sensor leverages the po...

SKU: AF-5967 | Brand: Adafruit

The Adafruit Proto Tripler PiCowbell gives your Raspberry Pi Pico or Pico W three side-by-side socket slots — plug in your Pico and up to two PiCowbell accessories with no soldering or stacking headers required. It al...

SKU: AF-5913 | Brand: Adafruit

The Adafruit STEMMA Reflective Photo Interrupt Sensor uses a TCRT1000 right-angle optical module to detect reflective surfaces. An onboard IR LED emits light, and when an object reflects it back to the IR phototransis...

SKU: AF-5907 | Brand: Adafruit

The Adafruit Terminal PiCowbell with Pre-Soldered Sockets gives your Raspberry Pi Pico or Pico W instant plug-and-play access to every GPIO pin via screw terminal blocks. Simply plug in your Pico and connect 18–26 AWG...

SKU: SF-KIT-23451 | Brand: SparkFun

Pogo pins make life so much easier when you are trying to program without having to solder a single thing, and when you attach them to an In-system programming (ISP) adapter, they become instantly better. This simple ...

SKU: SF-SEN-22956 | Brand: SparkFun

The SparkFun Photoacoustic Spectroscopy CO2 Sensor features the Infineon XENSIV PAS CO2 (PASCO2V01) sensor, which delivers highly accurate CO2 measurements in direct parts-per-million (ppm) format. The photoacoustic s...

SKU: DF-SEN0570 | Brand: DFRobot

Fermion: MEMS Smoke Gas Detection Sensor employs state-of-the-art microelectromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat...

SKU: DF-SEN0571 | Brand: DFRobot

Fermion: MEMS Odor Smell Gas Detection Sensor employs state-of-the-art microelectromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal...

SKU: DF-SEN0567 | Brand: DFRobot

Fermion: MEMS Ammonia NH3 Gas Detection Sensor employs state-of-the-art micro-electromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minim...

SKU: LB-COCKATOO | Brand: Little Bird

The Cockatoo is a simple screw-terminal breakout board for the BBC micro:bit. Slide your micro:bit into the edge connector and you get secure screw terminal access to pins 0, 1, 2, 3.3V, and GND — no soldering or croc...

SKU: AF-5709 | Brand: Adafruit

The Adafruit CAN Bus FeatherWing adds CAN bus networking to any Feather board. It uses the MCP2515 CAN controller and TJA1051/3 transceiver to send and receive messages in standard or extended format at up to 1 Mbps o...

SKU: SF-DEV-21247 | Brand: SparkFun

The SparkFun USB-C Host Shield provides all the digital logic and analogue circuitry needed to add USB peripheral/host control to your Arduino. Interface with and control any USB 2.0 compatible device — thumb drives, ...

SKU: DF-DFR0979 | Brand: DFRobot

The Gravity CH423 I2C 24 Digital IO Expansion Module extends your microcontroller with 24 additional digital output/input pins over a standard I2C connection. Based on the CH423 chip, it provides 8 GPIOs with interrup...

SKU: AF-5663 | Brand: Adafruit

Need to use multiple I2C devices that share the same address? The PCA9546 4-Channel I2C Multiplexer lets you connect up to four same-address I2C devices to a single microcontroller by acting as a gatekeeper — write a ...

SKU: AF-5611 | Brand: Adafruit

The Adafruit PCF8575 GPIO Expander Breakout is an affordable 16-channel I2C GPIO expander that doubles your available digital I/O over a simple two-wire connection. Add extra buttons, LEDs, relays, or other digital pe...

SKU: AF-5610 | Brand: Adafruit

The Adafruit LTR-303 is a low-cost I2C digital light sensor that provides 16-bit measurements for both infrared and visible+IR spectrums. Subtract one from the other to get human-visible light readings. With configura...