Breakouts

SKU: SF-SEN-22956 | Brand: SparkFun

The SparkFun Photoacoustic Spectroscopy CO2 Sensor features the Infineon XENSIV PAS CO2 (PASCO2V01) sensor, which delivers highly accurate CO2 measurements in direct parts-per-million (ppm) format. The photoacoustic s...

SKU: DF-SEN0570 | Brand: DFRobot

Fermion: MEMS Smoke Gas Detection Sensor employs state-of-the-art microelectromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat...

SKU: DF-SEN0571 | Brand: DFRobot

Fermion: MEMS Odor Smell Gas Detection Sensor employs state-of-the-art microelectromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal...

SKU: DF-SEN0567 | Brand: DFRobot

Fermion: MEMS Ammonia NH3 Gas Detection Sensor employs state-of-the-art micro-electromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minim...

SKU: LB-COCKATOO | Brand: Little Bird

The Cockatoo is a simple screw-terminal breakout board for the BBC micro:bit. Slide your micro:bit into the edge connector and you get secure screw terminal access to pins 0, 1, 2, 3.3V, and GND — no soldering or croc...

SKU: AF-5709 | Brand: Adafruit

The Adafruit CAN Bus FeatherWing adds CAN bus networking to any Feather board. It uses the MCP2515 CAN controller and TJA1051/3 transceiver to send and receive messages in standard or extended format at up to 1 Mbps o...

SKU: SF-DEV-21247 | Brand: SparkFun

The SparkFun USB-C Host Shield provides all the digital logic and analogue circuitry needed to add USB peripheral/host control to your Arduino. Interface with and control any USB 2.0 compatible device — thumb drives, ...

SKU: DF-DFR0979 | Brand: DFRobot

The Gravity CH423 I2C 24 Digital IO Expansion Module extends your microcontroller with 24 additional digital output/input pins over a standard I2C connection. Based on the CH423 chip, it provides 8 GPIOs with interrup...

SKU: AF-5663 | Brand: Adafruit

Need to use multiple I2C devices that share the same address? The PCA9546 4-Channel I2C Multiplexer lets you connect up to four same-address I2C devices to a single microcontroller by acting as a gatekeeper — write a ...

SKU: AF-5611 | Brand: Adafruit

The Adafruit PCF8575 GPIO Expander Breakout is an affordable 16-channel I2C GPIO expander that doubles your available digital I/O over a simple two-wire connection. Add extra buttons, LEDs, relays, or other digital pe...

SKU: AF-5610 | Brand: Adafruit

The Adafruit LTR-303 is a low-cost I2C digital light sensor that provides 16-bit measurements for both infrared and visible+IR spectrums. Subtract one from the other to get human-visible light readings. With configura...

SKU: SF-SEN-19096 | Brand: SparkFun

The SparkFun BME688 Environmental Sensor is a breakout that combines a gas scanning sensor with temperature, humidity, and barometric pressure sensing for a complete environmental sensor in a single package. The ga...

SKU: DF-SEN0501 | Brand: DFRobot

This multifunctional environmental sensor comprises SHTC3 temperature & humidity sensor, BMP280 barometric pressure sensor, VEML7700 ambient light sensor, and ML8511 UV sensor into one and offers 5 kinds of environmen...

SKU: AF-5315 | Brand: Adafruit

An 8-pin SOIC test clip with a DIP breadboard adapter, designed for in-circuit probing and programming of flash memory, EEPROMs, and other 8-SOIC ICs — no soldering or desoldering required. Simply clip onto the chip t...

SKU: DF-SEN0330 | Brand: DFRobot

This Digital Temperature & Humidity Sensor Breakout Board is based upon the Sensirion SHT30 sensor IC. Thanks to Sensirion’s CMOSens® technology, highly integrated capacitive humidity sensing components and band-gap t...

SKU: DF-SEN0333 | Brand: DFRobot

A high-accuracy digital temperature and humidity sensor breakout board based on the Sensirion SHT35 sensor IC. Using Sensirion's CMOSens technology, the SHT35 delivers excellent long-term stability, low power consumpt...

SKU: DF-DFR0914 | Brand: DFRobot

This DFRobot 4-channel optocoupler-isolated level converter translates 12V signals down to 5V, making it easy to interface industrial sensors and PLC outputs with Arduino and other 5V microcontrollers. Each channel fe...

SKU: AF-5189 | Brand: Adafruit

Keep track of time even when your project loses power or gets reprogrammed. This updated PCF8523 Real Time Clock breakout features STEMMA QT / Qwiic connectors for solderless I2C wiring, plus traditional breadboard he...

SKU: AF-5187 | Brand: Adafruit

The Adafruit SCD-40 is a photoacoustic true CO2 sensor that directly measures carbon dioxide concentration in ambient air, rather than estimating it from volatile organic compounds. It also includes integrated tempera...

SKU: SF-COM-16988 | Brand: SparkFun

The SparkFun QwiicBus EndPoint is the fastest and easiest way to extend the range of your I2C communication bus. The breakout uses NXP’s PCA9615 IC, which converts the two default I2C signals into four differential si...