Breakouts

SKU: DF-SEN0097 | Brand: DFRobot

This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more acurate and easier ...

SKU: DF-DFR0164 | Brand: DFRobot

This is a new version of the FTDI breakout board features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The 8U2 firmware uses the standard USB COM drivers, and no ...

SKU: SF-BOB-11771 | Brand: SparkFun

This is a breakout board for the Texas Instruments TXB0104 module. The TXB0104 is a 4-bit bidirectional voltage-level translator with automatic direction sensing. This 4-bit noninverting translator uses two separate...

SKU: AF-3070 | Brand: Adafruit

The Adafruit RFM69HCW Transceiver Radio Breakout @ 868/915 MHz is a breadboard-friendly packet radio module for adding long-range wireless communication to Arduino and other microcontroller projects. Based on the SX12...

SKU: SF-DEV-13743 | Brand: SparkFun

The SparkFun Level Shifting microSD Breakout is quite similar to the SparkFun microSD Transflash Breakout, but with the included level shifting hardware, this board allows you to utilize a microSD card at Arduino’s SD...

SKU: SF-BOB-13717 | Brand: SparkFun

This is the SparkFun Pi Wedge, a small board that connects to the 40-pin GPIO connector on the Raspberry Pi and breaks the pins out to breadboard-friendly arrangement and spacing, and even adds a couple of decou...

SKU: AF-284 | Brand: Adafruit

Note: These use genuine FTDI chips, either we purchase them or they are manufactured to our specifications with the requirement of genuine FTDI chips 10/22/14 - read more. Long gone are the days of parallel ports and ...

SKU: AF-1897 | Brand: Adafruit

The Adafruit SPI Non-Volatile FRAM Breakout provides 64 Kbit (8 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no pa...

SKU: SF-SEN-12642 | Brand: SparkFun

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of so...

SKU: AF-3533 | Brand: Adafruit

The Adafruit 0.96" 160×80 Colour TFT Display Breakout is a tiny, high-density full-colour screen driven by the ST7735R controller. Despite its thumbnail size, it packs 160×80 RGB pixels and communicates over 4-wire SP...

SKU: PL-2126 | Brand: Pololu

A breakout board for ST's LPS331AP digital barometric pressure sensor. This sensor measures absolute pressure from 260 to 1260 mbar with excellent accuracy (±2 mbar), making it ideal for altitude estimation, weather m...

SKU: SF-BOB-29094 | Brand: SparkFun

A breakout board for the Panasonic EVQWGD001 roller wheel encoder with press-to-select switch. This tactile input device combines a scrolling wheel with a push button in a compact form factor – similar to the scroll w...

SKU: AF-6348 | Brand: Adafruit

Add reliable wired Ethernet to your microcontroller project with the Adafruit Wiz5500 Ethernet Breakout Board. The WIZ5500 chip handles TCP/IP over SPI, letting you skip the hassle of WiFi passwords and antennas for a...

SKU: DF-TEL0150 | Brand: DFRobot

##Introduction This is a CAN-to-UART and USB 1.0 communication module that is compatible with both 3.3V and 5V. It supports the CAN 2.0 protocol and incorporates the SLCAN command, eliminating the need for you to conc...

SKU: AF-6067 | Brand: Adafruit

The Adafruit LPS28 Pressure Sensor Breakout features the ST LPS28DFW — a barometric pressure sensor with an extended range up to 4060 hPa, far beyond the ~1260 hPa limit of most competing sensors. This makes it suitab...

SKU: AF-6062 | Brand: Adafruit

The Adafruit INA3221 breakout monitors current, voltage, and power on up to three independent power rails simultaneously over I2C. Each channel supports high or low-side measurement up to +26V DC at ±3.2A with ±1% pre...

SKU: DF-SEN0617 | Brand: DFRobot

The Gravity BME688 is an advanced MEMS environmental sensor from Bosch that measures temperature, humidity, barometric pressure, and volatile organic compounds (VOC) in a single compact module. It supports both I²C an...

SKU: SF-SEN-24805 | Brand: SparkFun

The SparkFun Qwiic Ultrasonic Distance Sensor, a user-friendly upgrade to the popular HC-SR04 sensor, offers non-contact distance measurement from 2cm to 400cm with an accuracy of 3mm. This sensor is designed to seaml...

SKU: AF-5970 | Brand: Adafruit

The Adafruit TSMP96000 "Code Learning" Infrared IR Receiver Breakout detects IR signals across a wide frequency range of 20–60 KHz, making it perfect for "code learning" applications where you need your device to work...

SKU: AF-5964 | Brand: Adafruit

The Adafruit SEN54/SEN55 Adapter Breakout lets you quickly connect a Sensirion SEN5x environmental sensor node to any microcontroller or single-board computer via STEMMA QT / Qwiic — no soldering or breadboarding requ...