Breakouts

SKU: PR-PIM320 | Brand: Little Bird

A preposterous pile of peripherals on your Pi! Mix and match 3 HATs or 5 pHATs into a platter of functionality. Use pHAT Stack for specific setups and projects, or just as a handy way to use several HATs or pHAT...

SKU: PL-2482 | Brand: Pololu

The Pololu basic relay carrier modules allow simple control of a single-pole, double-throw (SPDT) switch from low-voltage, low-current control signals. This item includes the basic carrier PCB with a soldered-in 1...

SKU: PL-2128 | Brand: Pololu

The Black Edition of the A4988 stepper motor driver carrier features a four-layer PCB for better thermal performance, allowing the A4988 to deliver approximately 20% more current than the standard two-layer (green) ve...

SKU: SF-SEN-21274 | Brand: SparkFun

The SparkFun Qwiic Dynamic NFC/RFID Tag features the ST25DV64KC dynamic Near Frequency Communication (NFC) / Radio Frequency Identification (RFID) tag IC from STMicroelectronics©. The ST25DV64KC offers 64-kBit (8-kByt...

SKU: DF-DFR1036 | Brand: DFRobot

A 1-channel DAC module that converts a PWM signal from any microcontroller into a precise 0–5V or 0–10V analogue voltage output. Built around the GP8101S chip with 8-bit resolution and 0.2% accuracy, it's ideal for dr...

SKU: AF-5957 | Brand: Adafruit

The Adafruit DVI Sock is a compact DVI/HDMI output board designed to solder directly onto the end of a Raspberry Pi Pico or Pico W like a little PCB sock. Using the RP2040's PIO system, it enables your Pico to drive a...

SKU: PR-PIM311 | Brand: Little Bird

The Pico HAT Hacker gives you full access to all 40 GPIO pins on your Raspberry Pi, broken out at the top of the board. Its ultra-thin 0.8 mm PCB can be soldered directly onto the Pi's header pins while still leaving ...

SKU: PR-PIM277 | Brand: Little Bird

Add a tiny yet convenient power switch to your Pi with OnOff SHIM! Our SHIMs (Shove Hardware in the Middle) are a new range of boards designed to be small, affordable, and handy. They're just 0.8mm thick (the bare boa...

SKU: PR-PIM219 | Brand: Little Bird

The Mini Black HAT Hack3r is a compact breakout board that gives you full access to all Raspberry Pi GPIO pins while a HAT or pHAT is attached. Ideal for debugging HAT projects, probing signals, or combining a HAT wit...

SKU: AF-5947 | Brand: Adafruit

The Adafruit PiCowbell OV5640 Camera Breakout with 160° Wide-Angle Lens adds a 5-megapixel camera with an ultra-wide 160-degree field of view to your Raspberry Pi Pico or Pico W. The widest lens option in the PiCowbel...

SKU: FT-LEVEL | Brand: Freetronics

Many of the most interesting sensors and devices are only available in 3.3V or even lower voltage versions, which can be a problem if you want to connect them to a 5V microcontroller such as an Arduino. This module...

SKU: PR-PIM301 | Brand: Little Bird

Button SHIM gives you five handy, physical buttons and an RGB status LED, and it's HAT and pHAT-compatible! Our SHIM-format boards are designed to slip neatly onto your Pi's GPIO pins and still allow you to use HAT...

SKU: TB-XC4444 | Brand: Little Bird

A pyroelectric infrared (PIR) motion sensor module for Arduino and microcontroller projects. It detects movement from people and animals by sensing changes in infrared radiation, outputting a digital high signal when ...

SKU: SF-COM-09277 | Brand: SparkFun

A simple breakout board for 2×2 button pads with integrated LEDs. Each LED and button is brought out to side connectors, making wiring straightforward. The board also includes footprints for 1N4148 through-hole diodes...

SKU: PL-1182 | Brand: Pololu

A breakout board for the Allegro A4988 DMOS microstepping stepper motor driver with translator and overcurrent protection. It lets you control one bipolar stepper motor at up to 2 A per coil (with sufficient cooling) ...

SKU: PL-2990 | Brand: Pololu

Overview DRV8838 Single Brushed DC Motor Driver Carrier, bottom view with dimensions. TI SN754410 (16-pin DIP) next to the #2135 DRV8835 carrier (14-pin DIP) and #2990 DRV8838 carrier (10-pin DIP) for size re...

SKU: RP-SC0326 | Brand: Raspberry Pi

The Compute Module 4 IO Board is a companion board for Raspberry Pi Compute Module 4. It is designed for use both as a development system for Compute Module 4 and as an embedded board integrated into end products.The ...

SKU: SF-ROB-16836 | Brand: SparkFun

The SparkFun ProDriver makes it easy to start developing with the TC78H670FTG bipolar stepper motor driver from Toshiba! Latch terminals provide instant solder-less connections to every feature offered. Use our extens...

SKU: PR-PIM169 | Brand: Little Bird

The Mini Black HAT Hack3r is a compact breakout board that lets you access all 40 GPIO pins on your Raspberry Pi while a HAT or pHAT is attached. It connects between your Pi and the HAT via a ribbon cable, bringing ev...

SKU: PI-ESP004 | Brand: Pimoroni

This board has the same Bluetooth LE module that used on Puck.js and Pixl.js, pre-programmed with Espruino. Just apply power, connect with Bluetooth LE or Serial and start writing JavaScript! This is a boar...