Breakouts

SKU: LB-00038 | Brand: Little Bird

Geek Ammo's Australian Made Logic Level converter makes it possible to connect 3.3V (or even lower voltage sensors) to 5V micro controllers like the Raspberry Pi. With this module you can easily connect different...

SKU: AF-1362 | Brand: Adafruit

This breakout board is the simplest way to create a project with mutiple capacitive touch sensors. No microcontroller is required here - just power with 1.8 to 5.5VDC and connect up to 5 conductive pads to the 5 left-...

SKU: LB-00255 | Brand: Little Bird

An 8-channel voltage level converter module for shifting between 3.3V and 5V logic levels. Designed for use with Raspberry Pi, making it easy to interface with 5V sensors and modules from the Pi's 3.3V GPIO pins. Key...

SKU: LB-00331 | Brand: Little Bird

A small push-button switch module on a breakout board with a built-in pull resistor, so no external resistors are needed. The 3-pin header (signal, VCC, GND) plugs directly into a solderless breadboard or connects via...

SKU: SF-BOB-09322 | Brand: SparkFun

A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PCB has three connections for PWR, GND, and Signal.When the gate is clear, SIG will be high (>...

SKU: SF-SEN-12041 | Brand: SparkFun

If you need to add user input without using a button, then a capacitive touch interface might be the answer. The AT42QT1010 SparkFun Capacitive Touch Breakout offers a single capacitive touch button with easy-to-use d...

SKU: DF-DFR0239 | Brand: DFRobot

This small size breakout is programmable full-color RGB LED for hobbyists, industrial designers, prototypers, and experimenters. It is designed to allow the easy addition of dynamic indicators, displays, and lighti...

SKU: SF-BOB-11722 | Brand: SparkFun

This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB pins to standard, breadboard friendly, 0.1" headers. Turn it over and it has a foo...

SKU: SF-DEV-13664 | Brand: SparkFun

If you’re ready to step your Arduino game up from older 8-bit/16MHz microcontrollers, the SparkFun SAMD21 Mini Breakout is a great landing spot. The SAMD21 Mini Breakout is a Pro Mini-sized breakout for the Atmel ATSA...

SKU: AF-3182 | Brand: Adafruit

The Pimoroni Mini Black HAT Hack3r breaks out all 40 GPIO pins from your Raspberry Pi while still allowing a HAT or pHAT to sit on top. Connect via the included ribbon cable and access every pin — labelled with functi...

SKU: DF-FIT0324 | Brand: DFRobot

INTRODUCTION This adapter is especially designed for DFRobot 12V DC Motors, adding the compatibility factor for those products without customized connectors or external power supplies. ...

SKU: DF-DFR0072 | Brand: DFRobot

At sometime or another you may run out of pins on your Arduino board and need to extend it with shift registers.  With this shift out module which is based on 74HC595. The datasheet refers to the 74HC595 as an "8...

SKU: AF-6014 | Brand: Adafruit

This compact breakout board is designed for the Raspberry Pi 5 and Adafruit RP2350 boards that use an HSTX connector. These boards use a 22-pin FPC connection to carry high-speed video data over differential pairs, an...

SKU: AF-6318 | Brand: Adafruit

This driver board makes it much easier to control multiple solenoids from a microcontroller over I2C. It uses an MCP23017 GPIO expander so you do not need to dedicate lots of pins just to switch a bank of clicky, indu...

SKU: SF-GPS-29208 | Brand: SparkFun

Built around Septentrio’s mosaic-G5 P3, this compact GNSS RTK breakout is designed for projects that need survey-grade positioning without giving up space or power budget. It offers the same leading performance as the...

SKU: SF-SEN-30942 | Brand: SparkFun

Built around DYscan's DE2290D module, this SparkFun breakout brings 1D and 2D barcode scanning to USB and embedded projects. It uses CMOS image recognition with a 300,000-pixel global shutter camera, giving it the abi...