Breakouts

SKU: AF-3122 | Brand: Adafruit

Make your own custom DE-9 cable or DE-9 interface with ease, using this DE-9 Socket to Terminal Block Breakout. You get a nice solid PCB with an DE-9 socket and two strips of terminal blocks that you can use with stra...

SKU: SF-BOB-13021 | Brand: SparkFun

This is the SparkFun RJ45 MagJack Breakout, a simple board that will provide you with a way to put an ethernet port into your breadboard. The SparkFun RJ45 MagJack Breakout is the same one found in our very own mbe...

SKU: SF-PRT-10112 | Brand: SparkFun

This 2 mm pitch 10-pin header mates with 2 mm XBee sockets and is ideal for creating custom breakout boards, "dummy" XBee modules for testing, or any project requiring 2 mm pitch pin headers. Key Features 2 mm Pitc...

SKU: SF-DEV-09716 | Brand: SparkFun

This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact. Functionality has remained the same. This is a basic breakout board for the FTDI...

SKU: SF-PRT-10588 | Brand: SparkFun

Simple breakout board for the 3.5mm audio jack. Use this breakout (shipped bare) to allow breadboard or SIP access to the super-common 3.5mm audio jack. All five pins are broken out.

SKU: AF-5907 | Brand: Adafruit

The Adafruit Terminal PiCowbell with Pre-Soldered Sockets gives your Raspberry Pi Pico or Pico W instant plug-and-play access to every GPIO pin via screw terminal blocks. Simply plug in your Pico and connect 18–26 AWG...

SKU: LB-COCKATOO | Brand: Little Bird

The Cockatoo is a simple screw-terminal breakout board for the BBC micro:bit. Slide your micro:bit into the edge connector and you get secure screw terminal access to pins 0, 1, 2, 3.3V, and GND — no soldering or croc...

SKU: SF-DEV-21247 | Brand: SparkFun

The SparkFun USB-C Host Shield provides all the digital logic and analogue circuitry needed to add USB peripheral/host control to your Arduino. Interface with and control any USB 2.0 compatible device — thumb drives, ...

SKU: AF-5315 | Brand: Adafruit

An 8-pin SOIC test clip with a DIP breadboard adapter, designed for in-circuit probing and programming of flash memory, EEPROMs, and other 8-SOIC ICs — no soldering or desoldering required. Simply clip onto the chip t...

SKU: SF-COM-16988 | Brand: SparkFun

The SparkFun QwiicBus EndPoint is the fastest and easiest way to extend the range of your I2C communication bus. The breakout uses NXP’s PCA9615 IC, which converts the two default I2C signals into four differential si...

SKU: SF-PRT-17252 | Brand: SparkFun

The micro:bit Edge Connector allows you to expand the capabilities of the micro:bit development platform. This version of the connector features 80, right angle, PTH pins. Add this part to your board to create a handy...

SKU: PR-PIM171 | Brand: Little Bird

A handy breakout tool that lets you access all 40 GPIO pins while a HAT or pHAT is connected to your Raspberry Pi. Plug in your HAT, connect the ribbon cable to your Pi, and probe, debug, or extend any pin with ease. ...

SKU: SF-DEV-15096 | Brand: SparkFun

This SparkFun Serial Basic Breakout is an easy-to-use USB-to-Serial adapter based on the CH340G and takes advantage of the handy USB-C connector. With USB-C you can get up to three times the power delivery over the pr...

SKU: AF-1658 | Brand: Adafruit

Connect your own PCB to a Raspberry Pi with this extra-tall female header. The female header part has extra spaces to make it 13.6mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. This h...

SKU: AF-1833 | Brand: Adafruit

This breakout board gives you easy access to all 5 pins of a USB Micro-B connector via standard 0.1" header pins. It's a simple way to add USB 5V power to a project, interface with a USB-capable microcontroller, or pr...

SKU: AF-2102 | Brand: Adafruit

This 2×5 (10-pin) IDC breadboard helper makes it easy to connect standard 10-pin IDC ribbon cables to a breadboard or Perma-Proto board. The two-piece design consists of a pin-through socket that straddles the centre ...

SKU: SF-PRT-14417 | Brand: SparkFun

Here is a tiny 4-pin Qwiic 1mm JST connector. This connector is used on all of our Qwiic-based boards and can be used to create your own I2C-based device compatible with the Qwiic system!Additionally, this connector w...

SKU: AF-2888 | Brand: Adafruit

A BNC (Bayonet Neill–Concelman) male plug with a screw terminal block for solderless connections. Use stranded or solid-core wire and a small screwdriver to create custom wiring jigs for test equipment, video signals,...

SKU: SF-WRL-11812 | Brand: SparkFun

This is a simple to use, USB to serial base unit for the Digi XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, att...

SKU: AF-3118 | Brand: Adafruit

Make your own custom HDMI cable or HDMI interface with ease, using this HDMI Terminal Block Breakout. You get a nice solid PCB with an HDMI plug and two strips of terminal blocks that you can use with stranded or s...