Breakouts

SKU: SF-SEN-13322 | Brand: SparkFun

The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straight forward to use. The two large exposed pads function as probe...

SKU: AF-292 | Brand: Adafruit

LCD backpacks reduce the number of pins needed to connect to an LCD. LCDs are a fun and easy way to have your microcontroller project talk back to you. Character LCDs are common, and easy to get, available in tons ...

SKU: SF-BOB-13282 | Brand: SparkFun

This is a breakout board for the WS2812B RGB LED. The WS2812B is actually an RGB LED with a WS2811 built right into the LED! All the necessary pins are broken out to 0.1" spaced headers for easy bread-boarding. Severa...

SKU: SF-PRT-11214 | Brand: SparkFun

MOSFETs are awesome. They’re like a switch that you flip electronically! This SparkFun MOSFET Power Controller makes it easy to switch a battery supply on and off using your favorite microcontroller. The board also ha...

SKU: AF-334 | Brand: Adafruit

If you've got a resistive touch screen that you'd like to use, you'll need this breakout! It has a fine pitch (0.5mm) connector soldered onto it and it's broken out into the 4 resistive wires of the panel. A petite...

SKU: SF-SEN-13266 | Brand: SparkFun

The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by ...

SKU: SF-BOB-13263 | Brand: SparkFun

Introducing the 3.3V SparkFun FT231X Breakout board, complete with the full UART hardware handshake feature! The pin-out of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino board...

SKU: SF-SEN-11084 | Brand: SparkFun

Life has its ups and downs, so why not measure them? The MPL3115A2 is a MEMS pressure sensor that provides Altitude data to within 30cm (with oversampling enabled). The sensor outputs are digitized by a high reso...

SKU: SF-SEN-13030 | Brand: SparkFun

The SparkFun RFID Reader Breakout converts the 2mm pin spacing of ID-series RFID readers to breadboard-friendly 0.1" headers. Compatible with the ID-3LA, ID-12LA, and ID-20LA readers, this board lets you solder the re...

SKU: SF-WRL-10533 | Brand: SparkFun

A simple 315 MHz wireless receiver module that pairs with 315 MHz transmitters to create a basic one-way data link. It fits easily into a breadboard and works well with microcontrollers like Arduino for straightforwar...

SKU: SF-COM-10468 | Brand: SparkFun

The MSGEQ7 is a CMOS graphic equaliser IC that divides the audio spectrum into seven frequency bands: 63 Hz, 160 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.25 kHz, and 16 kHz. Each band is peak-detected and multiplexed to provide ...

SKU: AF-1897 | Brand: Adafruit

The Adafruit SPI Non-Volatile FRAM Breakout provides 64 Kbit (8 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no pa...

SKU: SF-BOB-10160 | Brand: SparkFun

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. Th...

SKU: DF-SEN0220 | Brand: DFRobot

The Gravity UART Infrared CO2 Sensor uses non-dispersive infrared (NDIR) technology to measure carbon dioxide concentrations from 0 to 50,000 ppm. It offers excellent selectivity with no oxygen dependency, built-in te...

SKU: SF-ROB-09454 | Brand: SparkFun

The SparkFun QRE1113 Line Sensor Breakout (Digital) is a compact IR reflectance sensor board that outputs a digital signal based on surface reflectivity. It uses a capacitor discharge circuit — the faster the 10 nF ca...

SKU: PL-2126 | Brand: Pololu

A breakout board for ST's LPS331AP digital barometric pressure sensor. This sensor measures absolute pressure from 260 to 1260 mbar with excellent accuracy (±2 mbar), making it ideal for altitude estimation, weather m...

SKU: SF-LCD-29467 | Brand: SparkFun

  The SparkFun Red Vision Touch Display for Pico features a 2.0", 320x240px capacative touch LCD mounted on a breakout board designed to plug directly into the Control Board on the Experiential Robotics ...

SKU: LB-COCKATOO-V2 | Brand: Little Bird

The Cockatoo v2 is a simple breakout board for the BBC micro:bit, designed for school projects involving basic lighting circuits. Slide the micro:bit into the edge connector and access three pins — Pin 2, 3.3 V, and G...

SKU: AF-5769 | Brand: Adafruit

The Adafruit Audio BFF is a compact add-on board that turns your QT Py or Xiao into a powerful audio playback device. It features a microSD card slot (up to 64 GB) and a MAX98357 I2S 3W amplifier, all designed to fit ...

SKU: DF-SEN0543 | Brand: DFRobot

This GR10-30 gesture sensor is capable of recognizing 12 hand gestures: move up, down, left, right, forward & backward, rotate clockwise & counterclockwise, rotate clockwise & counterclockwise continuously, hover, and...