Breakouts

SKU: AF-3133 | Brand: Adafruit

The Adafruit Ultimate GPS FeatherWing brings precise, low-power GPS to the Feather ecosystem. Built around the MTK3339 chipset, it tracks up to 22 satellites on 66 channels with -165 dBm sensitivity and delivers up to...

SKU: AF-3290 | Brand: Adafruit

A platinum resistance temperature detector (RTD) with a 100 Ω resistance at 0°C, offering superior accuracy and long-term stability compared to thermocouples and thermistors. PT100 sensors are widely used in laborator...

SKU: SF-BOB-10680 | Brand: SparkFun

A breakout board for the SOIC version of the 74HC595 8-bit shift register IC. Shift registers let you expand the number of digital outputs available on your microcontroller by clocking in serial data and latching it t...

SKU: SF-WRL-10535 | Brand: SparkFun

These wireless transmitters work with our 315MHz receivers. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they...

SKU: SF-PRT-10112 | Brand: SparkFun

This 2 mm pitch 10-pin header mates with 2 mm XBee sockets and is ideal for creating custom breakout boards, "dummy" XBee modules for testing, or any project requiring 2 mm pitch pin headers. Key Features 2 mm Pitc...

SKU: DF-DFR0019 | Brand: DFRobot

This is the very first prototyping shield for Arduino in the market since 2010. It comes with prototyping area that you can sold led , switch or other components, it also comes with a mini Arduino breadboard that can...

SKU: SF-DEV-09716 | Brand: SparkFun

This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact. Functionality has remained the same. This is a basic breakout board for the FTDI...

SKU: SF-PRT-10588 | Brand: SparkFun

Simple breakout board for the 3.5mm audio jack. Use this breakout (shipped bare) to allow breadboard or SIP access to the super-common 3.5mm audio jack. All five pins are broken out.

SKU: AF-5967 | Brand: Adafruit

The Adafruit Proto Tripler PiCowbell gives your Raspberry Pi Pico or Pico W three side-by-side socket slots — plug in your Pico and up to two PiCowbell accessories with no soldering or stacking headers required. It al...

SKU: AF-5907 | Brand: Adafruit

The Adafruit Terminal PiCowbell with Pre-Soldered Sockets gives your Raspberry Pi Pico or Pico W instant plug-and-play access to every GPIO pin via screw terminal blocks. Simply plug in your Pico and connect 18–26 AWG...

SKU: DF-SEN0570 | Brand: DFRobot

Fermion: MEMS Smoke Gas Detection Sensor employs state-of-the-art microelectromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat...

SKU: DF-SEN0567 | Brand: DFRobot

Fermion: MEMS Ammonia NH3 Gas Detection Sensor employs state-of-the-art micro-electromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minim...

SKU: LB-COCKATOO | Brand: Little Bird

The Cockatoo is a simple screw-terminal breakout board for the BBC micro:bit. Slide your micro:bit into the edge connector and you get secure screw terminal access to pins 0, 1, 2, 3.3V, and GND — no soldering or croc...

SKU: AF-5709 | Brand: Adafruit

The Adafruit CAN Bus FeatherWing adds CAN bus networking to any Feather board. It uses the MCP2515 CAN controller and TJA1051/3 transceiver to send and receive messages in standard or extended format at up to 1 Mbps o...

SKU: SF-DEV-21247 | Brand: SparkFun

The SparkFun USB-C Host Shield provides all the digital logic and analogue circuitry needed to add USB peripheral/host control to your Arduino. Interface with and control any USB 2.0 compatible device — thumb drives, ...

SKU: DF-DFR0979 | Brand: DFRobot

The Gravity CH423 I2C 24 Digital IO Expansion Module extends your microcontroller with 24 additional digital output/input pins over a standard I2C connection. Based on the CH423 chip, it provides 8 GPIOs with interrup...

SKU: SF-SEN-19096 | Brand: SparkFun

The SparkFun BME688 Environmental Sensor is a breakout that combines a gas scanning sensor with temperature, humidity, and barometric pressure sensing for a complete environmental sensor in a single package. The ga...

SKU: DF-SEN0501 | Brand: DFRobot

This multifunctional environmental sensor comprises SHTC3 temperature & humidity sensor, BMP280 barometric pressure sensor, VEML7700 ambient light sensor, and ML8511 UV sensor into one and offers 5 kinds of environmen...

SKU: AF-5189 | Brand: Adafruit

Keep track of time even when your project loses power or gets reprogrammed. This updated PCF8523 Real Time Clock breakout features STEMMA QT / Qwiic connectors for solderless I2C wiring, plus traditional breadboard he...

SKU: SF-PRT-18582 | Brand: SparkFun

This IR proximity contactless button makes for a good replacement for typical push buttons in situations where touching the button isn't required or desirable (especially in this day and age). This button includes a b...