Breakouts

SKU: AF-2029 | Brand: Adafruit

The Raspberry Pi B+/Pi 2/ Pi 3 has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our ...

SKU: AF-2471 | Brand: Adafruit

The Adafruit HUZZAH ESP8266 Breakout is a breadboard-friendly WiFi microcontroller board built around the Espressif ESP8266. With an 80 MHz processor, full WiFi client and access point support, a built-in TCP/IP stack...

SKU: AF-5907 | Brand: Adafruit

The Adafruit Terminal PiCowbell with Pre-Soldered Sockets gives your Raspberry Pi Pico or Pico W instant plug-and-play access to every GPIO pin via screw terminal blocks. Simply plug in your Pico and connect 18–26 AWG...

SKU: DF-SEN0567 | Brand: DFRobot

Fermion: MEMS Ammonia NH3 Gas Detection Sensor employs state-of-the-art micro-electromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minim...

SKU: LB-COCKATOO | Brand: Little Bird

The Cockatoo is a simple screw-terminal breakout board for the BBC micro:bit. Slide your micro:bit into the edge connector and you get secure screw terminal access to pins 0, 1, 2, 3.3V, and GND — no soldering or croc...

SKU: SF-SEN-19096 | Brand: SparkFun

The SparkFun BME688 Environmental Sensor is a breakout that combines a gas scanning sensor with temperature, humidity, and barometric pressure sensing for a complete environmental sensor in a single package. The ga...

SKU: SF-DEV-17047 | Brand: SparkFun

The SparkFun Qwiic GPIO adds eight additional digital I/O pins to your project via I2C, based on the TCA9534 I/O Expander from Texas Instruments. Read and write pins just like standard Arduino digital pins using the i...

SKU: SF-SEN-16295 | Brand: SparkFun

The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junc...

SKU: SF-BOB-15931 | Brand: SparkFun

Buttons are an easy and tactile way to interface with your project, but why would you want to deal with debouncing, polling, and wiring up pull-up resistors? The SparkFun Qwiic Button Breakout simplifies all of those ...

SKU: PR-PIM171 | Brand: Little Bird

A handy breakout tool that lets you access all 40 GPIO pins while a HAT or pHAT is connected to your Raspberry Pi. Plug in your HAT, connect the ribbon cable to your Pi, and probe, debug, or extend any pin with ease. ...

SKU: SF-SEN-09269 | Brand: SparkFun

Breakout board for the 3 axis ADXL335 from Analog Devices. This is the latest in a long, proven line of analog sensors - the holy grail of accelerometers. The ADXL335 is a triple axis MEMS accelerometer with extremely...

SKU: SF-SEN-13763 | Brand: SparkFun

A low-cost, highly accurate digital humidity and temperature sensor breakout board based on the Silicon Labs Si7021. Communicates over I²C with just two data lines, providing relative humidity and precise temperature ...

SKU: AF-2926 | Brand: Adafruit

The&nbsp;Terminal Block Breakout FeatherWing kit is like the Golden Eagle of prototyping FeatherWings (eg. majestic, powerful, good-looking). To start, you get a nice prototyping area underneath your Feather, wi...

SKU: AF-3417 | Brand: Adafruit

The FeatherWing Tripler lets you connect a Feather board to two FeatherWings side by side — no stacking headers needed. All three sets of pins are cross-connected, with dedicated GND and 3.3 V strips for easy power di...

SKU: SF-SEN-09836 | Brand: SparkFun

This new version adds 2 standoff holes as well as an extra decoupling capacitor. The ADXL345 is a small, thin, low power, 3-axis MEMS accelerometer with high resolution (13-bit) measurement at up to +-16 g. Digital...

SKU: AF-5906 | Brand: Adafruit

The Adafruit Proto Doubler PiCowbell gives your Raspberry Pi Pico or Pico W two side-by-side socket slots — plug in your Pico on one side and a PiCowbell accessory on the other, no soldering or stacking headers requir...

SKU: SF-COM-23979 | Brand: SparkFun

Does your microcontroller need to control a high-voltage item, like a 12V LED strip, while also needing to be powered? Do you want to avoid having multiple power adapters and microcontrollers for your project? The MOS...

SKU: SF-SEN-22494 | Brand: SparkFun

The STHS34PF80 sensor, from ST Microelectronics, is designed to measure the precise black-body radiation (as described by Planck's law) of an object; as well as monitor ambient temperature conditions within its 80° fi...

SKU: AF-5637 | Brand: Adafruit

The Adafruit QT 5V to 3V Shifter Breakout lets you safely connect 3.3 V STEMMA QT / Qwiic sensors to 5 V microcontrollers like the Arduino Uno. Many I2C sensors and Qwiic-compatible devices are not 5 V safe — connecti...

SKU: AF-5651 | Brand: Adafruit

An I2C breakout board for the RDA5807M FM radio chip, designed by ScoutMakes as a beginner-friendly introduction to electronics and wireless communications. Tune into FM stations, display RDS data (station and song na...