Brands

SKU: AF-2442 | Brand: Adafruit

Need to make a tiny robot? This little micro servo rotates 360 degrees fully forward or backwards, instead of moving to a single position. You can use any servo code, hardware or library to control these servos. ...

SKU: DF-FIT0085 | Brand: DFRobot

This custom-designed plastic wheel has a rubber tire measuring 1.65" (42 mm) in diameter and is designed to fit the output shafts on our mini metal gearmotors as well as the Solarbotics metal gear motors. Teeth on...

SKU: DF-SEN0032 | Brand: DFRobot

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos ...

SKU: DF-FIT0521 | Brand: DFRobot

This is a metal geared DC motor w/Encoder. It is a 6V motor with a 34:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 11 counts per revolution of the motor shaft, which corresponds ...

SKU: DF-FIT0121 | Brand: DFRobot

Jumper wires are one of the most important gear component for the tinkerer. Often underestimated, but one of the first things to miss. If you are starting to assemble your tinker gear and wondering if this is really n...

SKU: AF-2717 | Brand: Adafruit

The TCA9548A 1-to-8 I2C multiplexer solves the common problem of needing multiple I2C devices with the same address on a single bus. It acts as a gatekeeper, routing I2C traffic to any of its eight downstream channels...

SKU: DF-SEN0129 | Brand: DFRobot

INTRODUCTION This is an Arduino CH4 gas sensor. It uses MQ4 probe which is able to detect nature gas, CH4. It is less sensitivity in detecting alcohol, cooking fumes, and cigarette smok...

SKU: SF-BOB-09056 | Brand: SparkFun

A breakout board for the CD74HC4067 16-channel analogue/digital multiplexer/demultiplexer. This IC internally routes a common signal pin (SIG) to one of 16 channel pins, working with both analogue and digital signals ...

SKU: DF-FIT0190 | Brand: DFRobot

A 500-piece assortment of 0805 SMD resistors covering 25 common values from 620 Ω to 12 kΩ. Each value comes as a strip of 20 resistors, making it easy to keep your stock organised and identify values quickly. The 080...

SKU: AF-2927 | Brand: Adafruit

A Feather board without ambition is a Feather board without FeatherWings! This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 ...

SKU: SF-PRT-14017 | Brand: SparkFun

This 2x20 “tall” header has the same number and spacing of pins as a Raspberry Pi and provides your board with the ability to extend the heights of your GPIO to accommodate for enclosures or other parts that can en...

SKU: DF-FIT0314 | Brand: DFRobot

NFC Tag (13.56MHz) is widely used in electronic locks or customer identification as well as other systems where a small and easy to carry tag is desired.The tag contains a NXP S50 chip and an antenna, and is passi...

SKU: AF-2914 | Brand: Adafruit

A 3.5 mm (1/8") 4-pole TRRS audio plug with screw terminal connections — no soldering required. Use stranded or solid-core wire and a small screwdriver to create custom audio cables, breakouts, and test leads. TRRS s...

SKU: SF-PRT-11895 | Brand: SparkFun

A standard 8-pin female header with 0.1" (2.54 mm) pitch, designed for through-hole mounting. Connects with most standard 8-pin male headers. Specifications Pins – 8 Pitch – 0.1" (2.54 mm) Type – Female, through-...

SKU: SF-DEV-13903 | Brand: SparkFun

This is the LilyPad Rainbow LED strip, with seven LilyPad LEDs that are still attached to one another, letting you snap LEDs apart at your leisure to sew into clothing or whatever else you can dream up.The LilyPad Rai...

SKU: DF-DFR0026 | Brand: DFRobot

Here comes DFRobot's new Analog Ambient Light Sensor for Arduino or Raspberry Pi. Brand new design and much more convenient to use. This sensor help you to detect the light density and reflect the analog voltage s...

SKU: SF-CAB-00509 | Brand: SparkFun

A pair of banana plug to alligator clip cables in red and black, ideal for connecting multimeters, power supplies, oscilloscopes, and function generators to your circuit or test points. Specifications Connector A –...

SKU: AF-2988 | Brand: Adafruit

This spool of solid-core wire is easily soldered to and can handle up to 200°C and 600V. We like this wire because it's flexible but also holds its shape. We love the sturdiness and reliability fo...

SKU: DF-SEN0127 | Brand: DFRobot

  INTRODUCTION This is a generic Arduino gas sensor. It has MQ2 probe which is able to detect LPG, i-butane, propane, methane ,alcohol, Hydrogen, smoke.It can be used in gas leakage detecting device in c...

SKU: AF-157 | Brand: Adafruit

IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 3V to 5V so it's great for any microcontroller.To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to...