Brands

SKU: SF-TOL-10405 | Brand: SparkFun

This sewing needle set is designed for e-textile projects, with eye sizes large enough to easily thread conductive thread. The set includes both large and small needles to suit different stitching needs — from thick f...

SKU: AF-607 | Brand: Adafruit

A 32×32 full-colour RGB LED matrix panel with 1024 LEDs at 4mm pitch, measuring approximately 5 inches (128mm) square. These panels are commonly used in video walls and signage, delivering bright, vivid colours with g...

SKU: SF-ROB-12779 | Brand: SparkFun

The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). The EasyDriver requires a 6V to...

SKU: SF-BOB-12758 | Brand: SparkFun

The SparkFun Electret Microphone Breakout pairs a small electret microphone capsule with a 60× OPA344 op-amp preamplifier, making it easy to detect sound with a microcontroller's analogue-to-digital converter. Pick up...

SKU: SF-SEN-10289 | Brand: SparkFun

This AT407 basic tilt switch can easily be used to detect orientation. Inside the can is a ball that make contact with the pins when the case is upright. Tilt the case over and the balls don’t touch, thus not making a...

SKU: SF-SEN-10245 | Brand: SparkFun

A single-point load cell (strain gauge) rated for up to 50 kg. This is the same type of sensor found in digital bathroom scales. It outputs a small analogue voltage proportional to the applied force, which can be read...

SKU: SF-COM-10187 | Brand: SparkFun

The new generation 18 pin PICAXE microcontroller now has parallel tasking, touch sensors and more memory/RAM. See the Info Sheet for a comparison of features between the 18M2 and the 18M2+ PICAXE is a neat entr...

SKU: DF-FIT0482 | Brand: DFRobot

INTRODUCTION A new micro metal gear motor with a difference! This motor comes with a built-in encoder which measures the motor's speed in real time. The average output number of pulses ca...

SKU: SF-PRT-12639 | Brand: SparkFun

A 3.5mm TRRS (tip, ring, ring, sleeve) audio jack in a surface-mount package. Unlike standard stereo TRS connectors, TRRS provides three conductors plus ground, allowing it to carry stereo audio along with an addition...

SKU: DF-DFR0370 | Brand: DFRobot

The Arduino CAN BUS Shield V2 brings Controller Area Network (CAN bus) communication to your Arduino. Built around the MCP2515 CAN controller, it supports both standard and extended frames for transmitting and receivi...

SKU: AF-724 | Brand: Adafruit

Screw terminal blocks are the clean, maintainable solution for PCB-to-wire connections — no solder, no loose ends, easy to swap out later. These 3.5mm pitch 2-pin blocks are a practical size: wide enough for a range o...

SKU: AF-163 | Brand: Adafruit

A precision triple-axis accelerometer breakout featuring the Analog Devices ADXL335. With a ±3 g measurement range and analog outputs for X, Y, and Z axes, this sensor is ideal for tilt sensing, motion detection, and ...

SKU: AF-736 | Brand: Adafruit

With a slip ring assembly, your electronics can now twist and turn safely. Add wheel encoders, 360 degree sensors, rotating LEDs, rotors and more! We've seen a lot of people DIY slip ring's out of desperation but no l...

SKU: DF-ROB0128 | Brand: DFRobot

The Devastator is a tracked tank-style mobile robot platform built from high-strength aluminium alloy. This version 2 features upgraded metal DC gear motors for improved speed, torque, and durability compared to the o...

SKU: SF-TOL-12572 | Brand: SparkFun

These are nice, cross-locking, curved tweezers, unlike traditional models the tips on these tweezers will remain closed until squeezed open. They have a very fine tip which allows you to pick up very small parts with ...

SKU: SF-DEV-09873 | Brand: SparkFun

The SparkFun FTDI Basic Breakout provides USB-to-serial conversion using the FTDI FT232RL IC, operating at 3.3V logic levels. Its 6-pin header matches the standard FTDI pinout, making it compatible with Arduino Pro, L...

SKU: DF-FIT0495-I | Brand: DFRobot

This is a metal DC geared motor, 20:1 metal reducer. It has a small size and large torque. The maximum torque could arrive 0.7 kg.cm. It is stable and durable! SPECIFICATIONS Rated Voltage: 6 V Ope...

SKU: SF-CAB-09741 | Brand: SparkFun

These are good quality IC test hooks with a male connection wire. Instead of a single hook, these have two hooks that are capable of grabbing very small points (like SOIC IC legs). Comes in a bag of five IC hooks of d...

SKU: DF-DRI0039 | Brand: DFRobot

INTRODUCTION The latest quad motor driver shield for Arduino, compatible with 5V/3.3V Arduino controller, can control up to four DC motors with 8 pins at the same time. The shield supports P...

SKU: DF-DFR0012 | Brand: DFRobot

The Arduino Nano I/O Sensor Shield acts as an expansion board for the Arduino Nano and DFRduino Nano microcontrollers. There are several different options for power input. The form factor of the Nano I/O Shield bo...