Brands

SKU: DF-FIT0487 | Brand: DFRobot

INTRODUCTION A new micro metal gear motor with a difference! This motor comes with a built-in encoder which measures the motor's speed in real time. The average output number of pulses can reach up to 7*2*380...

SKU: SF-COM-10001 | Brand: SparkFun

Knobs are a great way to finish off your project and make it easier to adjust the level of your death ray. This knob mates to a 0.25" shaft. The knob slides onto the potentiometer and holds tightly with a strong frict...

SKU: AF-1935 | Brand: Adafruit

That's one tiny microphone! At about the size of a mature aphid, this wired Electret Microphone is perfect for your FONA. This microphone's very similar to our PCB-mount Elecret Microphone but is significantly sma...

SKU: SF-SEN-09836 | Brand: SparkFun

This new version adds 2 standoff holes as well as an extra decoupling capacitor. The ADXL345 is a small, thin, low power, 3-axis MEMS accelerometer with high resolution (13-bit) measurement at up to +-16 g. Digital...

SKU: SF-PRT-09835 | Brand: SparkFun

This is a simple 4 cell AA battery holder. The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel jack connector. The connector mates with the barrel jack on the Arduino (among a numbe...

SKU: DF-DRI0002 | Brand: DFRobot

A dual H-bridge DC motor controller based on the L298N driver chip, capable of driving two bi-directional DC motors at up to 2 A per channel. The module accepts a wide motor supply voltage of 4.8–46V and includes high...

SKU: AF-812 | Brand: Adafruit

Design a clock, timer or counter into your next project using our pretty 4-digit seven-segment display. These bright crisp displays are good for adding numeric output. Besides the four 7-segments, there are decimal...

SKU: DF-DRI0001 | Brand: DFRobot

The DFRobot 2×1A DC Motor Shield uses the L293 motor driver chip to control two 7–12 V DC motors at up to 1 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using pins 4, 5, 6, and 7 for mot...

SKU: DF-ROB0005 | Brand: DFRobot

The Turtle is a compact 2WD mobile robot platform designed for use with Arduino and other microcontroller boards. It comes as a kit with two geared DC motors, rubber wheels, a rear caster ball, an aluminium alloy chas...

SKU: DF-TEL0108 | Brand: DFRobot

This Bluetooth audio receiver module supports wireless streaming, USB flash drive, and TF (microSD) card playback. It decodes MP3, WMA, WAV, and lossless FLAC audio formats, with a built-in pre-amp output capable of d...

SKU: AF-824 | Brand: Adafruit

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male he...

SKU: AF-1949 | Brand: Adafruit

These Female/Female Jumper Wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainb...

SKU: AF-825 | Brand: Adafruit

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are approximately 3" (75mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1...

SKU: SF-SEN-09673 | Brand: SparkFun

A compact force sensitive resistor (FSR) from Interlink Electronics with a 4 mm (0.16″) diameter active sensing area. The resistance changes based on applied pressure — from over 1 MΩ with no pressure down to approxim...

SKU: DF-FIT0009 | Brand: DFRobot

This is a medium size breadboard with 600 tie points. It has strong, self-adhesive backing. It is ideal for high frequency and low noise circuits. SPECIFICATIONS   Size:170*65mm (6.7x2.6 in) Suitable for 0.3...

SKU: SF-COM-09592 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a green lens. It has a typical forward voltage of 2.0V and ...

SKU: SF-SEN-09570 | Brand: SparkFun

Melexis' MLX90614ESF-BAA is an infrared thermometer designed for non-contact temperature sensing. An internal 17-bit ADC and a powerful DSP contribute to the MLX90614’s high accuracy and resolution. It has a huge numb...

SKU: AF-2018 | Brand: Adafruit

Add a micro-slice standard solderless breadboard to your Perma-Proto or other perf-board. This 2x8 point solder-less breadboard is a good way to add some solderless prototyping space if you just need to...

SKU: DF-SEN0214 | Brand: DFRobot

The Gravity Analog 20A Current Sensor measures both AC and DC current using the Hall effect, outputting a proportional analog voltage to your microcontroller. With high-voltage isolation built into the circuit design ...

SKU: AF-865 | Brand: Adafruit

A red 4-digit 7-segment clock display with 0.56″ (14.2 mm) digit height. Each digit includes a decimal point, plus a centre colon for time-based displays. Bright at 18 mcd, these displays are easy to read and can be d...