Brands

SKU: AF-3647 | Brand: Adafruit

Precision-machined Swiss-pin male plug headers for a tight, reliable fit. Unlike standard stamped square-pin male headers, these use machined round pins that pair exclusively with Swiss-pin female sockets — they are n...

SKU: DF-SEN0230 | Brand: DFRobot

This is an industrial incremental photoelectric rotary encoder with aluminum material, metal shell and stainless steel shaft. It generates AB two-phase orthogonal pulse signal though the rotation of the grating dis...

SKU: AF-3662 | Brand: Adafruit

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need.  Absolutely no soldering required! All t...

SKU: AF-937 | Brand: Adafruit

This handy USB extension cable will make it easy for you to enclose a device that has a micro-B type port. We think this would be most handy when putting an Arduino Leonardo or Raspberry Pi in a box.The jack half h...

SKU: AF-1070 | Brand: Adafruit

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface.These sensors are easy to use, they are basically resistors that chan...

SKU: AF-1178 | Brand: Adafruit

Rollin' rollin' rollin', you can now roll around smooth as silk with these radial bearings. Often referred to as "skate bearings" They're good for supporting a rotating rod or as a wheel hub. However, these are higher...

SKU: LB-LS1216 | Brand: Little Bird

This sensor is composed of an infrared emitter on one upright and a shielded infrared detector on the other. By emitting a beam of infrared light from one upright to the other, the sensor can detect when an object pas...

SKU: LB-LS0070 | Brand: Little Bird

The knob is designed to set directly on the potentiometer's ridges so it's an easy & secure fit. It has a nice feel, with a solid grip, tweaking it is quite fulfilling This is the red version and it has a nice deep...

SKU: LB-LR0379 | Brand: Little Bird

This crimping tool can be used to crimp both male and female versions of our Tamiya connector crimp pins, mini Tamiya connector crimp pins, JST RCY connector crimp pins, JR crimp pins, Futa...

SKU: AF-1756 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-1755 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-2166 | Brand: Adafruit

A low-dropout (LDO) 3.3 V linear voltage regulator based on the ST L4931 in a TO-92 package. With just 0.4 V dropout, it delivers a clean, regulated 3.3 V output from input voltages as low as 3.7 V — well suited for s...

SKU: AF-2442 | Brand: Adafruit

Need to make a tiny robot? This little micro servo rotates 360 degrees fully forward or backwards, instead of moving to a single position. You can use any servo code, hardware or library to control these servos. ...

SKU: DF-FIT0085 | Brand: DFRobot

This custom-designed plastic wheel has a rubber tire measuring 1.65" (42 mm) in diameter and is designed to fit the output shafts on our mini metal gearmotors as well as the Solarbotics metal gear motors. Teeth on...

SKU: DF-SEN0032 | Brand: DFRobot

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos ...

SKU: DF-FIT0521 | Brand: DFRobot

This is a metal geared DC motor w/Encoder. It is a 6V motor with a 34:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 11 counts per revolution of the motor shaft, which corresponds ...

SKU: DF-SEN0129 | Brand: DFRobot

INTRODUCTION This is an Arduino CH4 gas sensor. It uses MQ4 probe which is able to detect nature gas, CH4. It is less sensitivity in detecting alcohol, cooking fumes, and cigarette smok...

SKU: AF-2927 | Brand: Adafruit

A Feather board without ambition is a Feather board without FeatherWings! This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 ...

SKU: SF-PRT-14017 | Brand: SparkFun

This 2x20 “tall” header has the same number and spacing of pins as a Raspberry Pi and provides your board with the ability to extend the heights of your GPIO to accommodate for enclosures or other parts that can en...

SKU: AF-2914 | Brand: Adafruit

A 3.5 mm (1/8") 4-pole TRRS audio plug with screw terminal connections — no soldering required. Use stranded or solid-core wire and a small screwdriver to create custom audio cables, breakouts, and test leads. TRRS s...