Brands and Manufacturers

SKU: EF-EF04093 | Brand: ElecFreaks

Octopus Analog UV sensor (GUVA-S12SD) is the UV electric brick in our Octopus series, the basic design is from the Octopus electric bricks and the setting of its outlook, the PCB fixing hole and the connectors are the...

SKU: AF-3893 | Brand: Adafruit

The JST PH 3-Pin to Male Header Cable converts a JST PH 3-pin connector into three individual colour-coded wires, each terminated with a 0.1" (2.54 mm) male header pin. It's ideal for extending sensor or LED connectio...

SKU: AF-3930 | Brand: Adafruit

This Reflective IR Sensor is a simple plastic casing with two elements - an IR LED and an IR phototransistor. You can control the IR LED and turn it on to bounce IR off objects to determine their reflectivity. Whit...

SKU: AF-1756 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-1755 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: DF-DFR0026 | Brand: DFRobot

Here comes DFRobot's new Analog Ambient Light Sensor for Arduino or Raspberry Pi. Brand new design and much more convenient to use. This sensor help you to detect the light density and reflect the analog voltage s...

SKU: AF-3178 | Brand: Adafruit

The Feather M0 RFM95 LoRa Radio (900 MHz) combines the ATSAMD21G18 ARM Cortex M0+ processor with an SX1276-based LoRa radio transceiver for long-range wireless communication at 868 or 915 MHz. The exact frequency is s...

SKU: DF-FIT0449 | Brand: DFRobot

INTRODUCTION This speaker module is based on the 8002 speaker amplifier IC. It can be used as a buzzer and also play high quality audio. Volume output is controlled via the potentiomet...

SKU: SF-ROB-09453 | Brand: SparkFun

This version of the QRE1113 breakout board features an easy-to-use analog output, which will vary depending on the amount of IR light reflected back to the sensor. This tiny board is perfect for line sensing applic...

SKU: DF-DFR0076 | Brand: DFRobot

This Gravity analog flame sensor detects fire and infrared light sources in the 760–1,100 nm wavelength range. With a 60° detection angle and analogue output proportional to flame distance, it's widely used in firefig...

SKU: AF-987 | Brand: Adafruit

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since...

SKU: AF-1789 | Brand: Adafruit

This 1K potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 1K ohm potentiometer, with a grippy shaft. Its smooth and easy to turn, but not so loose that it will ...

SKU: SF-SEN-00246 | Brand: SparkFun

This sensor uses an infrared emitted diode combined with an infrared phototransistor to detect the reflected infrared signal. Ideal for sensing black-to-white transitions or can be used to detect nearby objects (.5-1cm).

SKU: DF-DFR0023 | Brand: DFRobot

This is an Arduino Temperature Sensor based on LM35 temperature chip. A Temperature Sensor can be used to detect ambient air temperature.The LM35 chip is produced by National Semiconductor Corporation and offers a fun...

SKU: DF-SEN0043 | Brand: DFRobot

An analog ambient light sensor based on the TEMT6000 detector, which has a spectral response closely matching the human eye with very low IR sensitivity. It outputs an analog voltage proportional to the ambient light ...

SKU: AF-2765 | Brand: Adafruit

The Mini 2-Axis Analog Thumbstick is a compact, self-centring joystick with a black rocker cap, similar in style to PSP joysticks. It provides smooth directional analogue input using two 10 kΩ potentiometers — one for...

SKU: AF-1831 | Brand: Adafruit

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 100K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will...

SKU: AF-3406 | Brand: Adafruit

The Feather nRF52 Bluefruit LE is an all-in-one Bluetooth Low Energy development board built around the Nordic nRF52832. Unlike earlier Bluefruit Feathers that used a separate helper chip, the nRF52832 runs your appli...

SKU: DF-DFR0067 | Brand: DFRobot

This Gravity-compatible DHT11 sensor provides calibrated digital temperature and humidity readings via a single data pin. With an integrated 8-bit microcontroller and factory-calibrated coefficients stored in OTP memo...

SKU: AF-3481 | Brand: Adafruit

A panel-mount 10 kΩ logarithmic potentiometer with an integrated on/off switch. The logarithmic taper is designed for audio volume control — resistance increases on a curve that matches how the human ear perceives lou...