Brands and Manufacturers

SKU: AF-5578 | Brand: Adafruit

The BS612 is a compact, fully configurable mini PIR motion sensor that detects movement from approximately 3–8 metres away with a 120° detection spread. Its small form factor makes it ideal for unobtrusive motion-sens...

SKU: EF-EF04093 | Brand: ElecFreaks

Octopus Analog UV sensor (GUVA-S12SD) is the UV electric brick in our Octopus series, the basic design is from the Octopus electric bricks and the setting of its outlook, the PCB fixing hole and the connectors are the...

SKU: AF-3893 | Brand: Adafruit

The JST PH 3-Pin to Male Header Cable converts a JST PH 3-pin connector into three individual colour-coded wires, each terminated with a 0.1" (2.54 mm) male header pin. It's ideal for extending sensor or LED connectio...

SKU: AF-3930 | Brand: Adafruit

This Reflective IR Sensor is a simple plastic casing with two elements - an IR LED and an IR phototransistor. You can control the IR LED and turn it on to bounce IR off objects to determine their reflectivity. Whit...

SKU: SS-103030195 | Brand: Seeed Studio

The Grove Shield for micro:bit is a plug-and-play expansion board that bridges the micro:bit with the Seeed Studio Grove ecosystem. It provides 4 Grove connectors on-board (covering different interfaces) with provisio...

SKU: AF-1756 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-1755 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: DF-DFR0026 | Brand: DFRobot

Here comes DFRobot's new Analog Ambient Light Sensor for Arduino or Raspberry Pi. Brand new design and much more convenient to use. This sensor help you to detect the light density and reflect the analog voltage s...

SKU: AF-3178 | Brand: Adafruit

The Feather M0 RFM95 LoRa Radio (900 MHz) combines the ATSAMD21G18 ARM Cortex M0+ processor with an SX1276-based LoRa radio transceiver for long-range wireless communication at 868 or 915 MHz. The exact frequency is s...

SKU: DF-FIT0449 | Brand: DFRobot

INTRODUCTION This speaker module is based on the 8002 speaker amplifier IC. It can be used as a buzzer and also play high quality audio. Volume output is controlled via the potentiomet...

SKU: SF-ROB-09453 | Brand: SparkFun

This version of the QRE1113 breakout board features an easy-to-use analog output, which will vary depending on the amount of IR light reflected back to the sensor. This tiny board is perfect for line sensing applic...

SKU: DF-DFR0076 | Brand: DFRobot

This Gravity analog flame sensor detects fire and infrared light sources in the 760–1,100 nm wavelength range. With a 60° detection angle and analogue output proportional to flame distance, it's widely used in firefig...

SKU: SF-WRL-19177 | Brand: SparkFun

The SparkFun IoT RedBoard is an ESP32 Development Board that includes everything but the kitchen sink! Espressif's ESP32 WROOM is a powerful WiFi and Bluetooth® MCU module that targets a wide variety of application...

SKU: AF-5464 | Brand: Adafruit

This rubber sheet is made of the same carbon-black impregnated rubber material that our conductive rubber cord uses. Traditionally it would be used for EMF shielding, or conductive gaskets - but it's very fun to play ...

SKU: AF-987 | Brand: Adafruit

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since...

SKU: SS-110060024 | Brand: Seeed Studio

The Grove Starter Kit for Arduino from Seeed Studio is a beginner-friendly electronics kit built around the Grove modular connector system. It includes a Base Shield with multiple Grove connectors, twelve plug-and-pla...

SKU: AF-1789 | Brand: Adafruit

This 1K potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 1K ohm potentiometer, with a grippy shaft. Its smooth and easy to turn, but not so loose that it will ...

SKU: AF-1792 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: SF-SEN-00246 | Brand: SparkFun

This sensor uses an infrared emitted diode combined with an infrared phototransistor to detect the reflected infrared signal. Ideal for sensing black-to-white transitions or can be used to detect nearby objects (.5-1cm).

SKU: DF-DFR0023 | Brand: DFRobot

This is an Arduino Temperature Sensor based on LM35 temperature chip. A Temperature Sensor can be used to detect ambient air temperature.The LM35 chip is produced by National Semiconductor Corporation and offers a fun...