Brands and Manufacturers

SKU: EF-EF03405 | Brand: ElecFreaks

The Octopus:bit is a breakout board for the BBC micro:bit that extends all GPIO ports (P0–P16, P19–P20) into colour-coded pin headers with VCC and GND alongside each I/O pin. This makes connecting sensors, servos, and...

SKU: SF-CAB-15455 | Brand: SparkFun

This panel mount USB-C extension cable enables you to more easily enclose a project that contains a USB-C port. The cable is 6" in length and includes two 14mm M3 screws compatible with the cable's 3mm panel mount hol...

SKU: SF-SEN-14727 | Brand: SparkFun

This miniature straight bar load cell (sometimes called a strain gauge) can translate up to 100g of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that cha...

SKU: AF-2784 | Brand: Adafruit

ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 10K Ω Resistors. More specifically, they are carbon film, ...

SKU: AF-2781 | Brand: Adafruit

ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 470Ω Resistors. More specifically, they are carbon film, t...

SKU: AF-3950 | Brand: Adafruit

This cable will let you turn a JST PH 4-pin cable port into 3 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors o...

SKU: SF-WRL-14875 | Brand: SparkFun

A compact 1/4-wave rubber duck antenna for LoRa and other 860–960MHz communication. With a centre frequency of 915MHz and 2dBi gain, this 110mm antenna is ideal for space-constrained LoRa nodes where a smaller antenna...

SKU: AF-4130 | Brand: Adafruit

This RJ-45 round panel mount adapter provides an Ethernet pass-through connection that installs in a standard round drill hole — no rectangular cutouts or filing required. Drill a ~30 mm hole in wood, plastic, or meta...

SKU: PI-COM0404 | Brand: Pimoroni

A colourful 30 mm arcade-style pushbutton in blue. With a satisfying 2 mm travel and tactile click, these buttons are ideal for arcade builds, control panels, and interactive projects. Key Features Arcade Style – C...

SKU: LB-LS0657 | Brand: Little Bird

A high-fidelity DAC expansion board for Raspberry Pi that delivers superior audio quality over the Pi's built-in 3.5mm output. Built around Texas Instruments' PCM5122 DAC chip, this board connects via the I2S interfac...

SKU: LB-LR0214-50 | Brand: Little Bird

The 42BYG is a NEMA 17 bipolar stepper motor with a shaft-reversed design, commonly used in 3D printers, CNC machines, and DIY motion-control projects. With a 1.8° step angle and 40 N·cm holding torque, it provides re...

SKU: LB-LR0400 | Brand: Little Bird

A 1kg straight bar load cell (strain gauge) that converts applied force into a measurable electrical signal. Made from aluminium alloy with four strain gauges in a Wheatstone bridge configuration, this sensor is ideal...

SKU: AF-1468 | Brand: Adafruit

Get that heat sink stuck on good and strong with 3M's thermal tape. Specifically designed for attaching heat sinks to ICs. Works better and is less messy than thermal glues or pastes because the thickness is even acro...

SKU: LB-LR0281-9 | Brand: Little Bird

The TrinityPixel WS2812B is a 5-metre waterproof RGB LED strip featuring 30 individually addressable LEDs per metre (150 total). Each LED can be set to any 24-bit colour (8-bit PWM per red, green, and blue channel), g...

SKU: AF-1862 | Brand: Adafruit

A simple 2-pin connector soldered onto a breadboard-friendly breakout. This is compatible with the "JST PH 2-pin" connector. Mates perfectly with all our 1-cell LiPoly and LiIon batteries as well as our 6V coin ...

SKU: DF-DFR0094 | Brand: DFRobot

Infrared devices are widely used, and often for remote controlled devices. With this IR receiver, your Arduino project is now able to receive command from any IR remote controller. Well, it will be also easy...

SKU: DF-FIT0200 | Brand: DFRobot

This immersible pump can be used to water your plants, make a fountain or waterfall, even change your fish tank wter.It works quietly with the sound level under 30db. The pump has a filter inside as well as a suct...

SKU: AF-2796 | Brand: Adafruit

The Feather M0 Adalogger is an all-in-one datalogger built around the ATSAMD21G18 ARM Cortex M0 processor, with a built-in MicroSD card holder, native USB, and LiPo battery charging. With 256KB of flash and 32KB of RA...

SKU: DF-DFR0259 | Brand: DFRobot

Arduino RS485 is an industrial standard for long distance, anti-interferrence and reliable communication. So we create this RS485 Arduino shield, especially designed for the Arduino controller board. It convert...

SKU: DF-DFR0258 | Brand: DFRobot

This RS232 Shield For Arduino is designed for the Arduino controller,and it can easily convert UART to RS232 interface. The RS232 shield integrates DB9 connectors (female) that provide connection to various dev...