Brands and Manufacturers

SKU: DF-FIT0800 | Brand: DFRobot

A compact amphibious micro submersible pump perfect for building small fountains, automated plant watering systems, and DIY water projects. Powered by 3–6V DC, it features low noise operation, high efficiency, and eas...

SKU: AF-4401 | Brand: Adafruit

This 4-wire cable is a little over 200mm / 7.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching fe...

SKU: LB-PT-M38 | Brand: Little Bird

A compact Bluetooth 4.2 audio receiver module (MH-M18) that streams two-channel stereo audio wirelessly from your phone, tablet, or other Bluetooth device. Once paired, it delivers lossless audio playback with a conne...

SKU: LB-LR0024 | Brand: Little Bird

The rotary encoder is an electro-mechanical switch. Its output signal can be used to determine the direction that its knob is being rotated. Not only that, but it is also capable of continuous rotation, unlike a regul...

SKU: AF-3857 | Brand: Adafruit

The Feather M4 Express is built around the ATSAMD51J19, a 120 MHz Cortex M4 processor with hardware floating point and DSP instructions, 512 KB flash, and 192 KB RAM. It ships with CircuitPython pre-loaded — plug it i...

SKU: PL-1702 | Brand: Pololu

These premium jumper wires are stranded 26 AWG wires with male terminations on both ends, for use with 0.1″ (2.54 mm) fefemale headers, connectors, and solderless breadboards and breadboards. The assortm...

SKU: AF-1186 | Brand: Adafruit

OMG WATCH OUT! This 100mm diameter arcade button with a 16mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, howev...

SKU: LB-LR0555 | Brand: Little Bird

A great little project to help you learn to solder. This DIY heart shaped light up project comes with 18 bright LEDs to solder onto the board. They form a flashing pattern that repeats.  

SKU: LB-LR0214-37 | Brand: Little Bird

Other Features: Voltage: 3V / 5V; Amplification factor: 330; Wavelength: 609nm; A product for Arduino.1 x   Pulse sensor Pulse Heart Rate Sensor Module  

SKU: SF-TOL-09317 | Brand: SparkFun

This is a solderer’s best helper, the third hand. Comes with a heavy base, two alligator clips, a soldering iron holder, and a good magnifying glass. Note that we don’t normally need a third hand. It’s nice, but so...

SKU: SF-PRT-12044 | Brand: SparkFun

This red Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple circuits; They’re also great for breaking out DIP package ICs to jumpe...

SKU: SF-BOB-12009 | Brand: SparkFun

The SparkFun Bi-Directional Logic Level Converter safely translates signals between different voltage levels — stepping 5V down to 3.3V and 3.3V up to 5V on the same channel. It also works with 2.8V and 1.8V devices, ...

SKU: DF-DFR0251 | Brand: DFRobot

A relay is an electrically operated switch, which has a control system (also known as the input circuit) and the controlled system (also known as the output circuit), usually used in automatic control circuit. It i...

SKU: AF-64 | Brand: Adafruit

This is a cute half size breadboard, good for small projects. It's 2.2" x 3.4" (5.5 cm x 8.5 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the power rails off easily to...

SKU: SF-DEV-11235 | Brand: SparkFun

The Arduino and Breadboard Holder is a sturdy plastic base plate that keeps your Arduino and breadboard neatly organised during prototyping. The board mounts with two included screws using the standard Arduino mountin...

SKU: SF-ROB-13259 | Brand: SparkFun

These are a pair of basic, 65mm wheels with black rubber tires. These wheels are the same ones designed to fit onto DAGUs right angle gear motors utilized in the Magician Chassis and RedBot Kit. With these wheels you ...

SKU: DF-KIT0021 | Brand: DFRobot

A waterproof DS18B20 digital temperature sensor kit with everything you need to connect to an Arduino. The stainless steel probe measures temperatures from -55°C to +125°C over a 1-Wire interface, requiring just one d...

SKU: SF-PRT-12794 | Brand: SparkFun

These are 6" long jumper wires terminated as male to female. Use these to jumper from any male or female header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Comes in one pac...

SKU: DF-SEN0189 | Brand: DFRobot

The Gravity Analog Turbidity Sensor measures water clarity by detecting the level of suspended particles. It works by measuring light transmittance and scattering rate, which change with the amount of total suspended ...

SKU: AF-1950 | Brand: Adafruit

Premium female-to-female jumper wires in a convenient 20-pin ribbon cable, perfect for making wire harnesses or jumpering between headers on PCBs. Each wire is 150mm (6") long with 0.1" (2.54mm) female header contacts...