Arduino

SKU: AF-1768 | Brand: Adafruit

Build a large 60-LED NeoPixel ring with these quarter-ring segments. Each segment contains 15 individually addressable WS2812 5050 RGB LEDs arranged in a quarter circle — buy four and solder them together to complete ...

SKU: AF-1750 | Brand: Adafruit

The Synthetos gShield (formerly grblShield) V5 is a 3-axis CNC stepper motor driver shield for Arduino. Designed as a complete hardware companion for the grbl CNC motion control firmware, it turns an Arduino Uno into ...

SKU: AF-1733 | Brand: Adafruit

A rugged anemometer designed for outdoor wind speed measurement with a simple analog voltage output. Connect it to any microcontroller's analog input for easy wind speed readings — no complex protocols or libraries re...

SKU: AF-1032 | Brand: Adafruit

A gyroscope is a type of sensor that can sense twisting and turning motions. Often paired with an accelerometer, you can use these to do 3D motion capture and inertial measurement (that is - you can tell how an object...

SKU: AF-2026 | Brand: Adafruit

A 32×32 full-colour RGB LED matrix panel with 1024 LEDs at 5mm pitch. Designed for indoor use with a wide 160° viewing angle and pre-balanced white output, these panels look great in ambient light. The slightly larger...

SKU: AF-2279 | Brand: Adafruit

The 64×32 RGB LED Matrix Panel with 3mm pitch features 2048 bright RGB LEDs in a 192×96mm panel. With tighter pixel spacing than 4mm and 5mm variants, this panel delivers sharp images for indoor viewing at moderate di...

SKU: AF-2024 | Brand: Adafruit

The Adafruit Capacitive Touch Shield brings 12 channels of capacitive touch sensing to any Arduino using the MPR121 chip. Each sensor has a "figure 8" pad with holes designed for quick alligator clip connections — att...

SKU: DF-SEN0006 | Brand: DFRobot

The latest model SRF05 Detection range of 3 cm from the original SRF04 -3 m, increased to 1 cm -4 meters. RF04 is compatible with the original. Also has smaller side lobes. Ultrasonic module can be used to identi...

SKU: DF-SEN0005 | Brand: DFRobot

This low cost SFR02 ultrasonic ranger has both I2C and Serial interfaces. New AutoTune algorithms intelligently back the minimum range right up to the transducer ringdown for the very best performance possible, aut...

SKU: DF-TEL0026 | Brand: DFRobot

A Bluetooth 2.0 serial module for Arduino, featuring the CSR BC417143 chip with a double-board design for electrostatic protection. Provides transparent serial data communication over Bluetooth with a configurable bau...

SKU: DF-DFR0108 | Brand: DFRobot

The Arduino Mega 2560 Rev3 is a microcontroller board based on the ATmega2560, offering significantly more I/O than standard Arduino boards. With 54 digital I/O pins, 16 analog inputs, and 4 hardware serial ports, it'...

SKU: DF-DFR0091 | Brand: DFRobot

A 128 × 64 pixel graphic LCD module based on the ST7920 controller, featuring a blue backlight with white characters. Supports both parallel (8/4-bit) and SPI (3-wire serial) interfaces, with parallel mode set as the ...

SKU: DF-FIT0101 | Brand: DFRobot

This is a really easy use prototyping plate. Basically you can put everything from Arduino board to sensors, even a motor on top of it. It fits M2-M3 screws. NOTE: This product does not ship with the board shown abov...

SKU: DF-DFR0090 | Brand: DFRobot

An 8-digit serial LED display module that uses an SPI (3-wire) interface, requiring only three I/O pins from your Arduino or microcontroller. Multiple modules can be daisy-chained together for longer displays. The fli...

SKU: PL-2508 | Brand: Pololu

This shield makes it easy to build an Arduino-controlled Zumo robot. The shield mounts onto an assembled Zumo chassis, connecting directly to the chassis’s battery terminals and motors, and the Arduino plugs into ...

SKU: DF-DFR0117 | Brand: DFRobot

Arduino has a small amount of data storage space, The Arduino UNO has 32k. It doesn't have enough space if you want to store a lot of data. Therefore, we need to add an EEPROM Data Storage Module to increase its stora...

SKU: DF-SEN0228 | Brand: DFRobot

The Gravity VEML7700 is a high-accuracy digital ambient light sensor that outputs readings directly in lux (lx) over an I²C interface. Built around the Vishay VEML7700 IC, it features a 16-bit ADC, a high-sensitivity ...

SKU: DF-DFR0141 | Brand: DFRobot

The Rainbow LED Ring V3 features 12 individually addressable SMD RGB LEDs arranged in a ring, each controllable for brightness and colour. It comes with a pre-loaded bootloader containing several built-in LED animatio...

SKU: DF-DFR0021-R | Brand: DFRobot

A simple red LED module with a Gravity 3-pin digital interface for plug-and-play connection to Arduino and other microcontrollers via a Gravity IO Expansion Shield. Ideal for beginners learning digital output control....

SKU: AF-2547 | Brand: Adafruit

For advanced NeoPixel fans, we now have a bendable, Flexible 16x16 NeoPixel LED Matrix! Control all 256 ultra-bright LEDs using a single microcontroller pin, set each LED as you wish to scroll messages or draw litt...