Arduino

SKU: DF-FIT0140 | Brand: DFRobot

These are two pin jumpers (also called shunts) that will create an electrical connection for the 2.54mm(0.1") male pin headers. Commonly used to modify settings on a board or device. APPLICATIONS Jumpering pi...

SKU: DF-SEN0097 | Brand: DFRobot

This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more acurate and easier ...

SKU: DF-FIT0008-G | Brand: DFRobot

This is a very small breadboard with 170 tie points. This bread board is compatible with the Arduino Proto Shield. Strong self-adhesive backing. Measures 1.8"x1.4".You also have choices of different colors. SP...

SKU: DF-DFR0164 | Brand: DFRobot

This is a new version of the FTDI breakout board features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The 8U2 firmware uses the standard USB COM drivers, and no ...

SKU: DF-DFR0175 | Brand: DFRobot

This is a new IIC LCD backpack which supports Gadgeteer interface (IDC10). It allows gadgeteer user to play with LCD160X. The IIC LCD Backpack is a small PCB that can be soldered to the back of an LCD so tha...

SKU: DF-SEN0104 | Brand: DFRobot

This is a cool touch sensor from DFRobot. You can hook it up to the IO Expansion shield (for arduino) directly. It includes a metallic tape with a sticky side. This make it possible for you to place your sensors...

SKU: SF-PRT-14284 | Brand: SparkFun

These are 101mm long 26AWG jumpers with male connectors on both ends. Use these to jumper from any female header on any board to any other female header. Combine these with our female-to-female jumpers to create a ...

SKU: AF-2746 | Brand: Adafruit

The Adafruit Bluefruit LE Shield adds Bluetooth Low Energy connectivity to your Arduino in a plug-in shield form factor. Solder the included headers, stack it on your Arduino, and start communicating wirelessly with i...

SKU: SF-SEN-09198 | Brand: SparkFun

The Minisense 100 from Measurement Specialties is a low-cost cantilever-type vibration sensor loaded by a mass to offer high sensitivity at low frequencies. Useful for detecting vibration and ‘tap’ inputs from a user....

SKU: SF-SEN-09197 | Brand: SparkFun

A flexible piezo vibration sensor from Measurement Specialties, commonly used for detecting flex, touch, vibration, and shock. The PVDF polymer film generates a small AC voltage (up to ±90 V) when it moves, which can ...

SKU: DF-SEN0132 | Brand: DFRobot

INTRODUCTION This is an Arduino Carbon Monoxide Sensor. It uses MQ7 probe to detect Carbon Monoxide (CO) concentrations in the air from 20 to 2000ppm. The sensitivity ca...

SKU: SF-WRL-09143 | Brand: SparkFun

A 900/1800MHz dual-band duck antenna with 2dBi gain and an RP-SMA connector. Well suited for XBee 900MHz modules and other 900MHz radio applications. 50-ohm impedance, 105mm long. Specifications Frequency – 900/180...

SKU: DF-DFR0159 | Brand: DFRobot

The 5V DFduino Pro Mini V1.3(Arduino Pro Mini Compatible) is a microcontroller board based on the ATmega328.It is a 5V DFduino running the 16MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Ard...

SKU: AF-2771 | Brand: Adafruit

The Feather 32u4 Basic Proto is the no-frills member of the Feather 32u4 family, with a built-in prototyping area where you can solder on extra components like buttons, sensors, or connectors without needing a separat...

SKU: DF-FIT0227 | Brand: DFRobot

The MQ7 is a simple-to-use Carbon Monoxide (CO) sensor suitable for detecting CO concentrations in the air. It offers a wide detection range from 20 to 2000 ppm, making it ideal for safety monitoring and air quality p...

SKU: DF-SEN0138-R | Brand: DFRobot

A miniature snap-action switch, also trademarked and frequently known as a micro switch, is an electric switch that is actuated by very little physical force.Micro switches are very widely used; among their appl...

SKU: SF-BOB-08891 | Brand: SparkFun

This breakout board provides a convenient PCB adapter for MQ-series gas sensors (MQ-3, MQ-4, MQ-6, MQ-7, and MQ-8). It converts the sensor's oversized, oddly-spaced pins into a standard breakout format that's easy to ...

SKU: SF-PRT-08808 | Brand: SparkFun

This is a very simple but extremely handy, 1" square, single sided perf board. Standard 0.1" spacing with a 4-40 (3mm) hole for mounting. Every three holes are connected with a 20mil trace.  Package of 2

SKU: DF-SEN0139 | Brand: DFRobot

This is a K type Thermocouple (Temperature sensor) which is very popular for 3D printers such as Ultimaker and Makerbot. You can hardly damage them or mishandle them. You just need an additional IC (Like an AD595) ...

SKU: SF-SEN-08712 | Brand: SparkFun

This is a piezoresistive force sensor from Tekscan. The harder you press, the lower the sensor’s resistance. Pressing hard, the resistance changes from infinite to ~300k. The sensor itself is thin and flexible, but th...