Arduino

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: DF-DFR0296 | Brand: DFRobot

The Bluno Nano combines an Arduino Nano-compatible ATmega328 microcontroller with an integrated TI CC2540 Bluetooth 4.0 (BLE) module in a compact 53 × 19 mm form factor. It enables wireless communication, wireless pro...

SKU: DF-DFR0332 | Brand: DFRobot

Make an air aerial propeller vessel, a cooling system, or spinning machine with this small fan module. It comes with a propeller, a 15,000 rpm motor and cable. Add flavor to your own interesting projects with this ...

SKU: AF-1785 | Brand: Adafruit

A medium surface transducer that turns any flat surface — tables, walls, panels — into a speaker. Unlike traditional cone speakers, a voice coil wrapped around a metal rod causes vibration that transfers directly to t...

SKU: LB-LR0178-350 | Brand: Little Bird

SKU: DF-SEN0502 | Brand: DFRobot

This looks like a potentiometer, but it’s an encoder switch. It is a cascadable 360 ° rotary encoder switch with 20 pulses per revolution, and each pulse corresponds to a detent. There are LED lights set for each dete...

SKU: DF-TEL0142 | Brand: DFRobot

When building a project that needs to transmit some simple signals wirelessly, have you been bothered by the any of the following problems: Bluetooth's cumbersome AT command configuration and high cost, Wifi's signal ...

SKU: SF-SEN-18367 | Brand: SparkFun

A sealed, waterproof DS18B20 digital temperature probe for precise measurements in wet or harsh environments. The sensor communicates over a 1-Wire interface, requiring just one data pin (plus ground) to connect to yo...

SKU: EC-SEL71220A | Brand: Elecrow

A current sensing module based on the Allegro ACS712 Hall effect sensor, capable of accurately measuring both AC and DC current up to ±20 A. The module outputs a proportional analogue voltage that can be read directly...

SKU: DF-FIT0720 | Brand: DFRobot

These patch test hooks provide a solderless way to make signal and low-current connections between boards, sensors, and modules. The hook clips grab onto pins, pads, and component legs — perfect for prototyping with c...

SKU: EC-SEA0001T | Brand: Elecrow

The Crowtail Starter Kit for Arduino is a beginner-friendly electronics kit built around the Crowduino Uno-SD board and the Crowtail modular connector system. With 22 plug-and-play modules and over 20 guided tutorials...

SKU: EC-ACS70028DH | Brand: Elecrow

The Dual Channel H-Bridge Motor Shield is composed of 2 discrete MOSFET H-bridge, designed to drive two DC motor with max current 8A. It is made up of 8 N-channel MOSFET IRF3205S and 4 pcs of half bridge motor control...

SKU: EF-EF04093 | Brand: ElecFreaks

Octopus Analog UV sensor (GUVA-S12SD) is the UV electric brick in our Octopus series, the basic design is from the Octopus electric bricks and the setting of its outlook, the PCB fixing hole and the connectors are the...

SKU: AF-1405 | Brand: Adafruit

Get started with the fabulous Adafruit Flora platform with this lovely budget kit, just enough to get you started with this fun wearable computer. Included are enough parts to make your first wearable electronic pr...

SKU: DF-SEN0032 | Brand: DFRobot

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos ...

SKU: DF-SEN0129 | Brand: DFRobot

INTRODUCTION This is an Arduino CH4 gas sensor. It uses MQ4 probe which is able to detect nature gas, CH4. It is less sensitivity in detecting alcohol, cooking fumes, and cigarette smok...

SKU: AF-2927 | Brand: Adafruit

A Feather board without ambition is a Feather board without FeatherWings! This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 ...

SKU: SF-DEV-13903 | Brand: SparkFun

This is the LilyPad Rainbow LED strip, with seven LilyPad LEDs that are still attached to one another, letting you snap LEDs apart at your leisure to sew into clothing or whatever else you can dream up.The LilyPad Rai...

SKU: AF-157 | Brand: Adafruit

IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 3V to 5V so it's great for any microcontroller.To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to...