All Products

SKU: SF-BOB-11771 | Brand: SparkFun

This is a breakout board for the Texas Instruments TXB0104 module. The TXB0104 is a 4-bit bidirectional voltage-level translator with automatic direction sensing. This 4-bit noninverting translator uses two separate...

SKU: SF-SEN-13835 | Brand: SparkFun

The SST Liquid Level Sensor provides single-point liquid detection via a TTL-compatible push/pull output. Its miniature optical design allows installation in tight spaces where traditional float switches won't fit. A...

SKU: PL-1133 | Brand: Pololu

This compact carrier board from Pololu makes it easy to integrate a Sharp GP2Y0D815Z0F, GP2Y0D810Z0F, or GP2Y0D805Z0F digital distance sensor into your project. It provides all the required external components, an on-...

SKU: SF-BOB-13717 | Brand: SparkFun

This is the SparkFun Pi Wedge, a small board that connects to the 40-pin GPIO connector on the Raspberry Pi and breaks the pins out to breadboard-friendly arrangement and spacing, and even adds a couple of decou...

SKU: DF-SEN0143 | Brand: DFRobot

This Infrared Proximity Sensor made by Sharp (model: GP2Y0A41SKOF) has an analog output which varies from 3.1V (4cm) to 0.3V (30cm) with a supply voltage between 4.5 and 5.5V DC. This sensor is great for sensing obje...

SKU: SF-SEN-13285 | Brand: SparkFun

This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the ‘alarm’ pin will go low.This unit works great from 5...

SKU: SF-BOB-13282 | Brand: SparkFun

This is a breakout board for the WS2812B RGB LED. The WS2812B is actually an RGB LED with a WS2811 built right into the LED! All the necessary pins are broken out to 0.1" spaced headers for easy bread-boarding. Severa...

SKU: SF-PRT-11214 | Brand: SparkFun

MOSFETs are awesome. They’re like a switch that you flip electronically! This SparkFun MOSFET Power Controller makes it easy to switch a battery supply on and off using your favorite microcontroller. The board also ha...

SKU: SF-COM-10468 | Brand: SparkFun

The MSGEQ7 is a CMOS graphic equaliser IC that divides the audio spectrum into seven frequency bands: 63 Hz, 160 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.25 kHz, and 16 kHz. Each band is peak-detected and multiplexed to provide ...

SKU: DF-DFR0411 | Brand: DFRobot

INTRODUCTION This DC motor has an integrated transistor built in to the board, eliminating the need for a motor driver. Use PWM to control it for all your DIY project needs. It uses the 3 pi...

SKU: SF-ROB-09454 | Brand: SparkFun

The SparkFun QRE1113 Line Sensor Breakout (Digital) is a compact IR reflectance sensor board that outputs a digital signal based on surface reflectivity. It uses a capacitor discharge circuit — the faster the 10 nF ca...

SKU: DF-SEN0648 | Brand: DFRobot

The TOFSense F2P is a professional-grade laser distance sensor using dTOF (Direct Time-of-Flight) technology. With 50m range, ±3cm accuracy, and 100Hz refresh rate, it's engineered for drones, traffic monitoring, indu...

SKU: SF-BOB-28467 | Brand: SparkFun

A simple breakout board that converts the 22-pin HSTX/camera/display connector to standard 0.1" through-hole pins. Perfect for prototyping and debugging when you need direct access to all the signals from your RP2350 ...

SKU: SF-WRL-28434 | Brand: SparkFun

The SparkFun IoT RedBoard combines the powerful ESP32-D0WDQ6 microcontroller with MicroPython pre-installed, letting you start coding IoT projects right out of the box. No need for complex toolchains – just connect vi...

SKU: SF-BOB-29762 | Brand: SparkFun

  The WS2812 (often referred to as a "NeoPixel") has become the standard for addressable LED projects. This RGB LED Breakout board, now with pre-soldered right-angle headers, is the absolute easiest way to st...

SKU: KI-5698 | Brand: Kitronik

A compact motor driver board for the BBC micro:bit that drives two DC motors or one stepper motor. The integrated edge connector lets the micro:bit slot in directly, with built-in protection against short circuits, ov...

SKU: EC-SEE00804D | Brand: Elecrow

The All-in-one Starter Kit for ESP32-P4 is a complete learning platform built around Espressif's ESP32-P4, a high-performance 32-bit RISC-V dual-core microprocessor with powerful image and voice processing capabilitie...

SKU: KI-5038 | Brand: Kitronik

The Kitronik Air Quality Control HAT for Raspberry Pi lets you monitor, log, and react to environmental data using the BME688 sensor. It measures temperature, pressure, humidity, air quality index, and eCO2, with an o...

SKU: PL-3753 | Brand: Pololu

The Pololu Dual G2 High-Power Motor Driver 24v14 is a Raspberry Pi expansion board that can independently control two brushed DC motors at up to 14A continuous per channel. It mounts directly onto the Pi's 40-pin GPIO...

SKU: KI-5693 | Brand: Kitronik

With the Kitronik Compact Robotics Board, the BBC micro:bit can be used to drive 4 motors (or 2 stepper motors) and 8 servos. Coupled with 17 other I/O expansion points, this means the BBC micro:bit can very easily be...