All Products

SKU: AF-4470 | Brand: Adafruit

The Adafruit MCP4728 Quad DAC with EEPROM provides four independent 12-bit digital-to-analogue converters in a single I2C package. Set precise output voltages for your project, and save your settings to the built-in E...

SKU: LB-LR0285 | Brand: Little Bird

Feature: 0.5°C Ensured Accuracy (+25°C) Suitable for Remote Applications Low Cost Due to Wafer-Level Trimming Operates from 4 to 30 V Less than 60-μA Current Drain Low Self-Heating, 0.08°C in Still Air Low Impedance O...

SKU: AF-1699 | Brand: Adafruit

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm...

SKU: AF-1740 | Brand: Adafruit

This small (14mm diameter) piezo element is nicely enclosed so you can attach easily. Piezo elements convert vibration to voltage or voltage to vibration. That means you can use this as a buzzer for making beeps, tone...

SKU: SF-SEN-09088 | Brand: SparkFun

This is a very small light sensor. A photocell changes (also called a photodetector, photo resistor, CdS or photoconductive cell) resistance depending on the amount of light it is exposed to. These little sensors make...

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: AF-3377 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: SF-SEN-12650 | Brand: SparkFun

The AD8232 SparkFun Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as a...

SKU: AF-3393 | Brand: Adafruit

A dual-ganged 10K linear potentiometer with a built-in on/off switch — two components in one convenient panel-mount package. The dual 10 kΩ linear-taper pots share a grippy shaft that turns smoothly without shifting o...

SKU: PR-PIM082 | Brand: Little Bird

Explorer HAT Pro adds a lot of useful tools to your Raspberry Pi.It has digital inputs and outputs, capacitive touch pads, croc. clip compatible pads, coloured LEDs, analog inputs, motor drivers, and a mini ...

SKU: AF-5578 | Brand: Adafruit

The BS612 is a compact, fully configurable mini PIR motion sensor that detects movement from approximately 3–8 metres away with a 120° detection spread. Its small form factor makes it ideal for unobtrusive motion-sens...

SKU: DF-DFR0896 | Brand: DFRobot

The ESP32-S3-WROOM-1-N4 is a powerful Wi-Fi and Bluetooth LE MCU module built around the ESP32-S3 SoC. Featuring a dual-core Xtensa LX7 processor running at up to 240MHz, 4MB SPI flash, and hardware acceleration for n...

SKU: LB-LS1891 | Brand: Little Bird

HS1891 DAC Module CJMCU-1334 UDA1334A I2S DAC Audio Stereo Decoder Module Board 3.3V - 5V Feature: This fully-featured UDA1334A I2S Stereo DAC breakout is a perfect match for any I2S-output audio interface.&nbsp...

SKU: EC-SPM32100S | Brand: Elecrow

This Moisture Sensor can be used to detect the moisture of soil or your pet plant's water level, let the plants in your garden reach out for human help. With the Octopus Electronic Bricks interface can very easy to us...

SKU: EF-EF04093 | Brand: ElecFreaks

Octopus Analog UV sensor (GUVA-S12SD) is the UV electric brick in our Octopus series, the basic design is from the Octopus electric bricks and the setting of its outlook, the PCB fixing hole and the connectors are the...

SKU: LB-LS1673 | Brand: Little Bird

This Potentiometer Module is from our Micro:bit 24 bit kit. You're probably already familiar with using a potentiometer as they are commonly found on many electrical devices, such as in audio equipment where they a...

SKU: AF-3893 | Brand: Adafruit

The JST PH 3-Pin to Male Header Cable converts a JST PH 3-pin connector into three individual colour-coded wires, each terminated with a 0.1" (2.54 mm) male header pin. It's ideal for extending sensor or LED connectio...

SKU: AF-1070 | Brand: Adafruit

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface.These sensors are easy to use, they are basically resistors that chan...

SKU: AF-3930 | Brand: Adafruit

This Reflective IR Sensor is a simple plastic casing with two elements - an IR LED and an IR phototransistor. You can control the IR LED and turn it on to bounce IR off objects to determine their reflectivity. Whit...

SKU: SS-103030195 | Brand: Seeed Studio

The Grove Shield for micro:bit is a plug-and-play expansion board that bridges the micro:bit with the Seeed Studio Grove ecosystem. It provides 4 Grove connectors on-board (covering different interfaces) with provisio...