All Products
Showing 61-80 of 100 products
Gravity: Arduino Shield for Raspberry Pi B+/2B/3B/3B+/4B
The Gravity Arduino Shield for Raspberry Pi brings Arduino-compatible I/O to your Raspberry Pi B+, 2B, 3B, 3B+, or 4B. Built around the ATmega32u4 (Arduino Leonardo), it sits on top of your Pi and gives you access to all standard Arduino shields and sensors alongside the Pi's own GPIO, I2C, SPI, ...
Gravity: Arduino EC (Electrical Conductivity) Sensor / Meter
The Gravity EC (Electrical Conductivity) Sensor measures the conductivity of aqueous solutions, providing an analogue output for Arduino and compatible microcontrollers. EC measurement is essential for monitoring water quality, nutrient levels in hydroponic systems, and soil salinity in agricultu...
Gravity: I2C Digital Wattmeter
Gravity: I2C Digital Wattmeter is a high-resolution, high-precision, large-scale measurement module that can measure the voltage, current and power of various electronic modules and electrical equipment within 26V 8A, and the maximum relative error is no more than ±0.2% (A simple manual calibrati...
Gravity: Analog AC Current Sensor (5A)
When you want to measure the AC current, are you still having trouble cutting the wires, wiring or soldering. Gravity: Analog AC Current Sensor comes to the rescue, eliminating the need to cut wires or reconnect circuits. Simply clamp the AC transformer probe on the AC line, and then plug the 3.5...
Gravity: Analog AC Current Sensor (10A)
A non-contact AC current sensor with a clamp-on transformer probe, capable of measuring 0–10 A AC. Simply clamp the probe around an AC line and connect the 3.5 mm plug to the signal conversion module — no wire cutting or circuit modification required. The Gravity analogue interface outputs a 0.2...
Yahboom RTR self balance smart robot car for Arduino
The Yahboom RTR Self-Balancing Robot Car is a ready-to-run two-wheel balancing vehicle powered by an Arduino Uno. Using an MPU6050 gyroscope and a PID-based balance algorithm, the robot maintains stable upright balance with automatic posture recognition to control the balance system on and off. T...
Gravity: I2C 4-20mA DAC Module (Arduino Compatible)
The Gravity I2C 4-20mA DAC Module outputs 0–25 mA of current controlled via I2C, with high-accuracy 4–20 mA output available after calibration (0.2% linearity error). Built around the GP8302 chip, it provides 12-bit resolution and is compatible with Arduino, enabling precise current-loop control ...
Hackster & DFRobot EEDU Enviromental Sensor Kit (ESP32)
The Hackster and DFRobot EEDU Environmental Sensor Kit provides everything you need to get started with IoT environmental monitoring using an ESP32-based FireBeetle board. Build practical projects that monitor soil moisture, air quality, and environmental conditions in real time. The kit centres...
Gravity: Analog Current Sensor 50A (AC/DC) V2
·
##Introduction This is an updated version. Retired Product: Gravity: Analog 50A Current Sensor (AC/DC) V1Get this low-power current sensor to monitor your project every second for saving energy or protecting the circuit!This fully integrated Hall Effect-based linear STK-600/M current sensor gives...
Gravity: GP8503 2-Channel 12bit I2C to 0-2.5V/VCC DAC Module
·
##Introduction This is a 2-channel analog voltage output DAC module with I2C communication, 12-bit resolution, and 0.1% precision. It is well-suited for control projects operating within the 3.3V range, such as ESP32, Raspberry Pi, STM32, and other microcontrollers that require analog signal outp...
Gravity: GP8501 2-Channel PWM to 0-2.5V/VCC DAC Module
·
##Introduction This is a 2-channel analog voltage output DAC module with PWM communication, 8-bit resolution, and 0.5% precision. It is well-suited for control projects operating within the 3.3V range, such as ESP32, Raspberry Pi, STM32, and other microcontrollers that require analog signal outpu...
Gravity: GP8512: 1-Channel 15bit I2C to 0-2.5V/VCC DAC Module
·
##Introduction This is a 1-channel analog voltage output DAC module with I2C communication, 15-bit resolution, and 0.01% precision. It is well-suited for control projects operating within the 3.3V range, such as ESP32, Raspberry Pi, STM32, and other microcontrollers that require analog signal out...
Heatsink Compound
A 5g syringe of white thermal compound (also known as thermal grease or thermal paste) for improving heat transfer between components and heatsinks. Essential for any project where heat dissipation is critical. Composed of 50% silicone, 20% carbon, and 30% metal oxide with a thermal conductivity...
Micro:bit Driver Expansion Board
Since the advent of micro:bit, its simple and practical way of programming is widely loved by makers, students and teachers. Its sample design, coupled with a wealth of pin resources, give it infinite possibilities. This expansion board not only leads to 9 micro:bit onboard GPIO interfaces, ...
USB Charger for 7.4V LiPo Battery
Still using a big, bulky, traditional power adapter to charge your lithium battery? DFRobot provides you with a compact and efficient 7.4V lithium battery USB charger, only the size and weight of an ordinary Gravity sensor. With just a mobile phone AC adapter (or power bank) and an Android dat...
UNIHIKER K10 AI Educational Tool for Beginner (Image Detection, Voice Recognition, TinyML)
·
The UNIHIKER K10 is an AI learning device designed for education, serving as both a STEM AI kit and a TinyML education kit for teens. It integrates a 2.8-inch color screen, Wi-Fi, Bluetooth, a 2MP camera, microphone, speaker, RGB light, temperature sensor, humidity sensor, light sensor, an...
Gravity: Arduino DC Fan Module
Make an air aerial propeller vessel, a cooling system, or spinning machine with this small fan module. It comes with a propeller, a 15,000 rpm motor and cable. Add flavor to your own interesting projects with this module. This module is commonly used for STEM class. SPECIFICATIONS ...
Gravity: 4-Digital LED Segment Display Module (Red)
A 4-digit 7-segment LED display module from DFRobot's Gravity series. This red LED display communicates over I2C, making it easy to wire up with just two data lines and compatible with a wide range of microcontrollers. The module supports 8-level brightness adjustment, so you can fine-tune the d...
Gravity: 9 Pcs Sensor Set for Arduino
This is DFRobot's basic sensor set for arduino. Set includes light sensor, touch sensor, temperature sensor, magnetic sensor, vibration sensor, tilt sensor, big button, LED lighting module and Grayscale sensor. To connect these sensors to Arduino, we suggest to use our IO expansion shield...
Gravity: Arduino pH Sensor Meter Pro
This is a professional Arduino pH Sensor Meter Kit with industrial electrode. It has built-in simple, convenient , practical connection and long life (up to 1 year), which makes it very suitable for long term online monitoring. It has an LED which works as the Power Indicator, a BNC connector...
